manualshive.com logo in svg

GUITAR KIT WORLD EXP-style Guitar Kit, Assembly Manual

Share
Download
GUITAR KIT WORLD EXP-style Guitar Kit Assembly Manual Download Page 24

1. Remember the colors you use for each (in most cases black is used for ground

wires).

2. Solder a wire to one of the outside lugs that will be used for the neck pickup.
3. Do the same for the lug on the opposite side for the bridge pickup.

Next connect the wire you will use for your output wire to the two lugs joined in the center of
the switch. Lastly, connect the ground wire to the last remaining lug.

Test your connections by lightly pulling on the wires and install the pickguard. Mark out your
pilot holes and install the screws as we have done previously for installing hardware.

Installing the Pickups

Install both pickups as we have done previously and secure into place. Thread all wires,
including pickup selector and neck and bridge pickup wires through the hole at the side of
the bridge pickup cavity and place the guitar on its face. You can tape the different wires
together to help keep track of them.

Ground the volume pots and installing the capacitor

Connect the ground lugs (the lugs on the left if facing away) to the back of the casing. This
can be done by either bending back the ground lug and soldering into place, or using a
short wire.

Next take the capacitor (the small green filter) and connect to the output (middle) lug of the
tone pot and back of the tone pot case.

Connecting the pickup selector to the volume pots

Next we’ll connect the outputs of our volume pots to the pickup selector.

Do this by soldering the two wires used for the pickups (the two outside lugs on the pickup
selector switch) to the output (middle lug) of the respective volume pot. So, connect the
neck pickup selector wire to the neck volume pot for example.

24

Summary of Contents for EXP-style Guitar Kit
































Reviews:

No comments

Brands by name

Popular brands

Load more brands