background image

 

 

Safety and Compliance User Notices 

 

This GPR-device is certified according to FCC, subpart 15, IC RSS-220 and ETSI EN 302 066-

1&2. 
 

You  are  cautioned  that  changes  or  modifications  not  expressly  approved  by  the  party 

responsible for compliance could void the user’s authority to 

operate the equipment. 

 

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference in a residential installation. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance with 

the instructions, may cause harmful interference to radio communications. However, there is 
no guarantee that interference will not occur in a particular installation. If this equipment does 

cause  harmful  interference  to  radio  or  television  reception,  which  can  be  determined  by 
turning the equipment off and on, the user is encouraged to try to correct the interference by 

one  or  more  of  the  following  measures: 

Reorient  or  relocate  the  receiving  antenna. 

Increase the separation between the equipment and receiver. 

Connect the equipment into 

an outlet on a circuit different from that to which the  receiver is connected. 

Consult the 

dealer or an experienced radio/TV technician for help. 

 

According to the regulations stated in ETSI EN 302 066-1 (European 
Telecommunication Standards Institute): 

The control unit should not be left 

ON

 when leaving the system unattended. It should always 

be turned 

OFF

 when not in use. 

 
The  antennas  should  point  towards  the  ground,  walls  etc.  during  measurement  and  not 

towards the air. 

 

The antennas should be kept in close proximity to the media under investigation. 
 

Canadian and US regulations state that whenever GPR antennas are in 
use the following notes apply: 

This Ground Penetrating Radar device shall be operated only when in contact with or within 

1m of the ground. 

 

Only law enforcement agencies, scientific research institutes, commercial mining companies, 
construction  companies  and  emergency  rescue  or  firefighting  organizations  shall  use  this 

Ground Penetrating Radar Device. 

 

This device complies with Industry Canada license-exempt RSS standards. Operation is subject 
to the following two conditions: (1) This device may not cause interference and (2) this device 

must accept any interference, including interference that may cause undesired operation of the 
device. 

 

 

Summary of Contents for MALA



















Reviews: