background image

 

12 

 
 
 
 
 

LIMITED WARRANTY 

 
For one (1) year from the date of original purchase, The Guest Co., Inc. will, at its discretion, repair 
or  replace  for  the  original  consumer,  free  of  charge,  any  parts  found  defective  in  material  or 
workmanship.  All transportation charges under this warranty must be borne by the consumer.   

 

Proof of purchase is required:  a computerized register receipt is required. Hand written receipts are 
not accepted for warranty proof of purchase.  In the absence of a receipt, warranty period will be 
calculated from date of manufacture printed or stamped on the product. 
 
THERE IS NO OTHER EXPRESSED WARRANTY.  IMPLIED WARRANTIES, INCLUDING THOSE 
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE 
YEAR  FROM  THE  DATE  OF  PURCHASE.  THIS  IS  THE  EXCLUSIVE  REMEDY  AND 
CONSEQUENTIAL DAMAGES ARE EXCLUDED WHERE PERMITTED BY LAW. 
 

 

 
Tel: (707) 226-9600   

 

 

 

 

 

 

E-mail: [email protected]  

Fax: (707) 226-9670 

Website: www.marinco.com 

730199 Rev B  3429

 

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Summary of Contents for 729825













Reviews: