General Safety Instructions
Prior to the initial use of the unit, the operating instructions
should be read completely. If in doubt with regard to
connection and operation of the unit, consult the manufacturer
(servicing department).
FOLLOW THE INSTRUCTIONS BELOW CAREFULLY IN
ORDER TO SECURE A HIGH DEGREE OF SAFETY:
CAUTION!
•
The unit shall always be fitted on the worktable
horizontally, safely and firmly.
•
The workplace shall be kept clean and sufficiently lit.
•
Never use the unit near easily flammable materials,
gases or liquids.
•
Wear goggles, ear protectors and suitable protection
clothing. If necessary, use a breathing mask.
•
Always wear suitable clothing. Do not wear loose
garments or jewels, they could be caught by rotating
parts. Anti-skid footwear is recommended. If your hair is
long, wear a hairnet.
•
Make sure that your standing is stable when working with
the unit.
•
Keep unauthorised persons, children in particular, away
from the working area.
•
Keep the existing protection devices at places and
provide for their perfect functioning.
•
Make sure that the power cable is not close to rotating
parts.
•
Never leave the switched-on unit unattended. If you
depart from the unit, switch it off.
•
If the unit is out of use, prior to maintenance/cleaning or
replacement of a tool, unplug it.
•
Do not leave any adjustment wrenches in the unit. Before
switching the unit on, make sure that all the adjustment
wrenches and tools are removed.
•
For longer pieces to be worked, it is necessary to get
additional support.
•
The unit is allowed for use with a corresponding exhaust.
•
Do not touch sander belt and disk with hands.
•
Persons unable to operate the appliance due to their
physical, sensory or mental abilities or their
inexperience or lack of knowledge must not operate
it.
•
If the appliance or feeder cable show any sign of
visible damage the appliance must not be put into
operation.
•
If the feeder cable of the appliance is damaged it
needs to be replaced by the producer or an
electrician.
•
Repairs of the appliance can only be executed by an
electrician. There might be significant risks as a
result of unauthorised repairs.
•
The same regulations apply for accessories
.
Güde GmbH & Co. KG does not answer for damages
caused by:
•
Appliance damage by mechanical influences and
overloading.
•
Any changes to the appliance.
•
Use for any other purpose than that described in the
Operating Instructions.
•
Unconditionally follow all safety instructions to
prevent accidents and damage.
The unit is allowed for operation on the mains with a
faulty current switch (FI)
Emergency procedure
Conduct a first-aid procedure adequate to the injury and
summon qualified medical attendance as quickly as possible.
Protect the injured person from further harm and calm them
down.
For the sake of eventual accident, in accordance with DIN
13164, a workplace has to be fitted with a first-aid kit. It is
essential to replace any used material in the first-aid kit
immediately after it has been used.
If you seek help,
state the following pieces of information:
1. Accident
site
2. Accident
type
3.
Number of injured persons
4. Injury
type(s)
Disposal
Disposal instructions are given by pictographs on the unit or
packaging. For meaning of individual symbols refer to chapter
“Symbols on Unit”.
Operator Requirement
The operator shall read the instruction manual carefully before
using the unit.
Qualification
No special qualification is required for use of the unit except for
detailed direction by a professional.
Minimum Age
Only persons above 16 years of age are allowed to work with
the unit. Exempted from the provision is the use of the juvenile
trainees if they work in the course of their professional training
with an aim to obtain the skill under a trainer supervision.
Training
Use of the unit requires adequate lesson by a professional or
the use of the manual only. Special training is not required.
Technical Data
Supply connection
230 V
Frequency/Protection type
50 Hz / IP 2
0
Protection class
I
Max. output P
1
7
50 W
Motor speed
2800 min
-1
Work area l x w:
265 x 159 mm
Ø sander disk ca:
20
2
mm
Sander belt dimensions l
x w:
914 x 100 mm
Stop inclination:
0-45°
Sander belt inclination :
0-90°
Connection cable:
2 m / H05 VV-F
Weight ca:
20
kg
Dimensions l x w x h
(mm):
500 x 510 x 400 mm
Ordering No.:
75840
Transportation and Storage
The unit has been designed for stationary use.
Units out of use should be stored in a dry locked room.
9
Summary of Contents for 6500 PRO
Page 2: ...1 2 3 4 5 6 2 4 5 1 3 6 2...
Page 3: ...7 8 10 9 11 12 3...
