background image

5

Expert Power Sequencer 8112 

 

                                                                                                                                                                                                              © 2021 GUDE Systems GmbH

Device Description

1

Device Description

1.1

Security Advice

·

The device must be installed only by qualified personnel according to the following in-
stallation and operating instructions. 

·

The manufacturer does not accept responsibility in case of improper use of the device
and particularly any use of equipment that may cause personal injury or material dam-
age.

·

The device contains no user-maintenable parts. All maintenance has to be performed
by factory trained service personnel.

·

This device contains potentially hazardous voltages and should not be opened or dis-
assembled.

·

The device can be connected only to 230V AC (50 Hz or 60 Hz) power supply sock-
ets.

·

The power cords, plugs and sockets have to be in good condition. Always connect the
device to properly grounded power sockets.

·

The device is intended for indoor use only. Do NOT install them in an area where ex-
cessive moisture or heat is present.

·

Because of safety and approval issues it is not allowed to modify the device without
our permission.

·

Please note the safety advises and manuals of connected devices, too.

·

The device is NOT a toy. It has to be used or stored out or range of children.

·

Care about packaging material. Plastics has to be stored out of range of children.
Please recycle the packaging materials.

·

In case of further questions, about installation, operation or usage of the device, which
are not clear after reading the manual, please do not hesitate to ask our support team.

·

Please, never leave connected equipment unattended, that can cause damage.

·

Connect only electrical devices that do not have limited  on-time.  I.e.  in  case  of  failure,
all  connected  appliances  have  to  cope  with  a  continuous  on-time  without  causing
damage.

1.2

Content of Delivery

The package includes:

·

Expert Power Sequencer 8112

·

Quick Start Guide

1.3

Description

The 

Expert Power Sequencer 8112

 is a PDU that switches load outputs with delay to

avoid voltage peaks

·

6 power ports can be switched in a controlled switching sequence by switches on the
unit or by external pushbuttons

Summary of Contents for EPS 8112-1

















Reviews: