GÜDE 86031, Operating Manual

Page: 9 / 42

- NEVER use this cleaner together with flammable, toxic
fluids/substances that could negatively influence its
proper operation.
- Never aim water stream towards people, machine itself,
electric parts or other electrical devices.
- NEVER use cleaner outdoor on rain.
- Store this cleaner out of reach from children and
unauthorized people – RISK OF INJURY.
- NEVER touch plug or socket with wet hands.
- NEVER use high pressure cleaner with damaged power
cord.
- NEVER use high pressure cleaner with damaged high
pressure hose.
- NEVER let high pressure cleaner unattended.
- All conductible parts MUST be protected against water
stream.
- Plug the high pressure cleaner into the electric source
(230V/50 Hz) with grounding.
- High pressure can cause kick back from different parts.
Therefore always wear protective clothing and safety
goggles.
- Before any maintenance work on the cleaner you need
to plug it out from the power source.
- FOLLOW the Water supplier regulations, OTHERWISE
THERE IS A RISK OF WATER SOURCES POLLUTION.
- Maintenance or repairs of electric parts CAN be done by
professionals ONLY.
- Before disconnecting the hose from high pressure
cleaner it is necessary to RELEASE excess pressure
from the hose.
- Running the pump dry can cause heavy damage to
gasket system.
- If you want to unplug, don’t pull the cord.
- During the colder period of the year it is necessary to
store the high pressure cleaner in the place protected
from frost.
Follow the regulations of your water supplier. Possibly there
can be a system distributor installed to avoid regressive flow
to drinking water supply (cleaning detergent).
Diameter of used cable must correspond with the cable
length, i.e. longer cable must have bigger diameter and vice
versa. For details see table. Clean the inlet water filter
regularly!
Voltage
V
Elongation
till 25 m
Elongation
till 50 m
MOTOR
220 -230
240
Diameter
3X1,5mm²
Diameter
3X2,5mm²
- Install the high pressure cleaner close to the water
supply if possible.
- Operation of the high pressure cleaner is allowed only
with accessories and spare parts recommended by the
manufacturer. Using original parts and accessories
ensure safe and defect free function of the high pressure
cleaner.
- Place the high pressure cleaner on firm and safe
foundation.
- High pressure cleaner is designed for vehicles cleaning
only, especially for removing heavy pollution by using
clean water and bio degradable cleaning detergents.
- For domestic use only, not for professional use (industry,
crafts)
- Motor vehicle cleaning is allowed only in facility equipped
with oil separation
Commissioning
Using the machine is allowed only with 30 mA RCD
(residual current device)!
Vacuum cleaner
- Take the vacuum cleaner out of the multifunctional case
- Choose a nozzle and put it on the suction hose. Plug the
hose to one of the side holes depending on the required
function (suction or blowing).
- Insert the plug into the socket at the back of the
multifunctional case.
Warning: Socket is active only if turning button is in this
position (pict
.
3/2)
- By pressing the ON/OFF button you will start the vacuum
cleaner
High pressure cleaner
Join the high pressure hose with coupling of high pressure
spray gun by using fork wrench (SW 17)
(pict. 2).
Insert the high pressure lancet or washing brush into the gun.
By turning the angle variable nozzle you can set required
lancet jet.
-
Connect the high pressure hose to high pressure cleaner
outlet
(pict. 1/6)
Connect water supply hose to the high pressure cleaner inlet
(pict. 1/5)
Hose diameter must be at least 13mm and the hose itself
shall be reinforced.
-
Set the mode change-over to position “0”.
Socket for plugging in the high pressure cleaner must
have all characteristics stated on the type label (voltage
and frequency – V/Hz)
- If you have all parts connected turn the water supply on
- Water temperature at the outlet cannot exceed
50°C.
- WARNING: High pressure cleaner can be
operated with clean water only
Machine is now prepared for operation
Operation
Vacuum cleaner
Dry suction: Use cloth filter.
Wet suction:
Never use cloth filter.
High pressure cleaner
Open the water tap on max.
Turn the high pressure cleaner on
(pict. 3/2)
By pressing the gun you will start cleaning.
Cleaning detergent:
If you want to fill up both tanks, press the button next to the
socket, unscrew the tank lid and take the tank out.
After filing, screw the lid back on and put the tank into right
holders.
You can fill up tanks with two different cleaning detergents
because they are not connected.
With the gun pressed, set the required mixture proportion by
manipulation with turning button
(pict. 3/1) .
Each tank is released separately. You can release only one
tank in the time. When one tank is empty, turn the button
(pict. 3/1) into the position 0 and set second tank.
After the end of work
- Turn the high pressure cleaner off
- Shut the water supply
- Release excess pressure from the gun until all water
comes out from the nozzle head.
- Plug it out from socket
9