background image

11

Declaration of Conformity

EG-Ko

n

formitätserklärung

EC Declaration of Conformity

Hiermit erklären wir,

Güde GmbH & Co. KG

We herewith declare,

Birkichstrasse 6, 74549 Wolpertshausen, Germany,

daß das nachfolgenden bezeichneten Geräte aufgrund ihrer Konzipierung und
Bauart sowie in der von uns in Verkehr gebrachten Ausführungen den einschlägigen,
grundlegenden Sicherheits- und Gesundheitsanforderungen der EG-Richtlinien
entspricht.

that the following Appliance complies with the appropriate basic safty and health
requirements of the EC Directive based on its design and type, as brought into
circulation by us.

Bei einer nicht mit uns abgestimmter Änderung der Geräte verliert diese
Erklärung ihre Gültigkeit.

In a case of alternation of the machine, not agreed upon by us, this declaration will
lose ist validity.

Bezeichnung der Geräte:

- Metallbandsäge MBS 115 E

Machine Description:

Artikel-Nr.:

-  40536

Article-No.:

Einschlägige EG-Richtlinien:

- Maschinenrichtlinie 89/292/EWG

Applicable EC Directives:

EG-Richtlinie Elektromagnetische Verträglichkeit

  89/336/EWG mit Änderungen

Angewandte harmonisierte
Normen:
Applicable harmonized
Standards:

Datum/Herstellerunterschrift:

19.07.2001,

Date/Authorized Signature:
Angaben zum Unterzeichner:

Hr. Arnold, Geschäftsführer

Title of Sinatory:

-

 

EN 55014-1: 1993 + A1

-

 

EN 61000-3-2: 1995 + A13

-

 

EN 61000-3-3: 1995

-

 

EN 55014-2: 1997

Summary of Contents for 40536












Reviews: