manualshive.com logo in svg

Guardian SCC 25, Manual

Share
Download
Guardian SCC 25 Manual Download Page 1

                                                                                                                                       Page 1

GUARDIAN SCC-40

Issue (Auto VI) & V3.6t 07/12/00

GUARDIAN

SCC

40/35/30/25

Screw Compressor Controllers

•

 

Compressor status monitor with pressure, temperature, slide and load
displays

•

 

Control by suction pressure setpoint or remote 5

th

 pressure

•

 

Control by  suction equivalent temperature setpoint or remote 5

th

temperature

•

 

Alarm and trip monitoring

•

 

Compressor, pump, slide and speed control

•

 

Economiser, heater and liquid injection control

•

 

Optional Automatic volumetric slide control

•

 

Multiple compressor system control

•

 

Local panel operation and set-up

•

 

Communications for remote monitoring and set-up

•

 

Auto VI Control

Operation and Set-up Manual

GUARDIAN  SCC-40/35/30/25 Screw Compressor Controllers provide suction pressure
setpoint control and alarm monitoring for one screw compressor. Alternatively the unit may
be set-up to control on water chiller, glycol chiller or equivalent temperature.

GUARDIAN

Tel.  +44 (0) 1270 760599
Fax. +44 (0) 1270 766804

Email: 

[email protected]

www.Guardian-controls.com

Summary of Contents for SCC 25
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands