background image

 G

uar

di

an

 F

al

l P

ro

te

ct

io

 63

05

 S

. 2

31

st 

St

., 

Ken

t, 

W

A

 9

80

32 

 

2

Worker Classifications

!

CAUTION

Understand the following definitions of those who
work near or who may be exposed to fall hazards.

Qualified Person:

 A person with an accredited degree or certification, and with extensive experience or

sufficient professional standing, who is considered proficient in planning and reviewing the conformity of fall
protection and rescue systems.

Competent Person:

 A highly trained and experienced person who is ASSIGNED BY THE EMPLOYER to be

responsible for all elements of a fall safety program, including, but not limited to, its regulation, management,
and application. A person who is proficient in identifying existing and predictable fall hazards, and who has
the authority to stop work in order to eliminate hazards.

Authorized Person:

 A person who is assigned by their employer to work around or be subject to potential or

existing fall hazards.

It is the responsibility of a Qualified or Competent person to supervise the job site and ensure all
applicable safety regulations are complied with.

Product Specific Applications

Personal Fall Arrest:

 Big Boss HLL may be used to support a MAXIMUM 4 personal fall arrest

systems (PFAS) for use in Fall Arrest applications. Structure must withstand loads applied in the
directions permitted by the system of at least 5,000 lbs. Maximum free fall is 6‘, or up to 12’ if
used in combination with equipment explicitly certified for such use. Applicable D-ring: Dorsal.

Restraint:

 Big Boss HLL may be used in Restraint applications by a MAXIMUM 4 users. Restraint

systems prevent workers from reaching the leading edge of a fall hazard. Always account for fully
deployed length of lanyard/SRL. Structure must withstand loads applied in the directions
permitted by the system of at least 1,000 lbs. No free fall is permitted. Restraint systems may
only be used on surfaces with slopes up to 4/12 (vertical/horizontal). Applicable D-rings: Dorsal,
Chest, Side, Shoulder.

!

WARNING

Use of equipment in unintended applications may result in serious

injury or death. Maximum 1 attachment per connection point.

For all applications: worker weight capacity range

(including all clothing, tools, and equipment) is 130-310 lbs.

NEVER for simultaneous use in Fall Arrest and Restraint.

Summary of Contents for Big Boss HLL













Reviews: