background image

26

• 

These two (2) terminals provide communication connections for dual gate applications where one 

 

 

unit operates as a master and the other as slave operator.

• 

Shielded twisted pair must be used. The shield (drain wire) connection should be connected at  

 

 

Master Unit Only to the 

liNK coM

 terminal but not both.

• 

Connect the 

Dual liNK

 terminals of the two operators together.

• 

Connect the 

liNK coM

 terminals of the two operators together.

• 

Set OPTIONS DIP Switch #2 and #3 accordingly.

• 

If these terminals are not connected, each operator will automatically operate in single mode, if

 

DIP #3 is in MASTER position (OFF). If DIP #3 is set to the SLAVE position (ON) the unit is

 

non-functional.

•      

Recommended Belden Wire®, 22 AWG, type 8761, 9461, 9451, 1266A or equivalent.

       

1-pair shielded with drain wire. 

Available at your local electrical supply store.

Dual Gate Link Connection

Installing a Dual Gate Operator System

IMPORTANT:

  

 With a dual gate system certain control board settings and connections are required on the MASTER 

unit only and some are required on both the MASTER and the SLAVE unit. The list below gives an overview.

• 

gate sequencing

 - DIP #2 on Master Unit

•  

alarms

 - wired to MASTER only

•  

entry Devices

 - can be wired to either unit

•  

adjustable auto close

 - MASTER controls opening and closing for both gates)

•  

locks

 - controlled by the MASTER unit

•  

setting limits

 - set DIP#3 on each operator to MASTER position (OFF) in order to set the limit for each 

 

gate. After the limit is set, DIP #3 can be set to SLAVE (ON) position for dual mode operation. 

ALARM

STATUS

DUAL

LINK

AT OPEN

LIMIT

PRISON

MODE

+  ACC.  PWR.

12VDC

-  300ma

ALARM

STATUS

DUAL

LINK

AT OPEN

LIMIT

PRISON

MODE

+  ACC.  PWR.

12VDC

-  300ma

A

C

C.

 PO
WER

DU
AL C

ABLE

+12Vdc

COM

DUAL LINK

LINK COM

A

C

C.

 PO
WER

DU
AL C

ABLE

+12Vdc

COM

DUAL LINK

LINK COM

NOTE:

  

Do not combine AC and low voltage

wire in the same conduit.

Drain wire connects

at 

Master

 unit only.

Summary of Contents for GP-SW050






































Reviews: