background image

 

 

 

 

• 

  All installation and operations must follow federal, provincial, state, and local codes for wire plumbing, and installing chimney.  

• 

  All work must be performed by qualified personnel only. 

• 

  Read and understand all precautions before operating the furnace. 

• 

  Furnace not to be used as a standalone unit. It is recommended that a backup system be in place. 

• 

  Retain this manual as long as you own your Crown Royal Stove. Carefully read and follow these directions. Regularly read over 

this manual to keep you informed. 

 

 

 

 

WARNING!!

 

 

• 

  All installations and operations of your furnace must follow 

STATE, PROVINCIAL and LOCAL LAWS pertaining to 
operations, wiring, plumbing, and building codes. The 
installation must be performed by a qualified installer. 

• 

  Only burn coal in this unit. (Check with provincial, state, and 

local regulations that obtain to banned fuels in designated 
locations) 

• 

  Do not install this unit on a combustible surface. 

• 

  All models operate at atmospheric pressure. DO NOT 

obstruct, block or plug the overflow vent tube in any way, 
which is located on top of the furnace. 

• 

  You must open the chimney flue before opening the furnace 

door. 

• 

  This unit cannot be hooked to a chimney already serving 

another appliance. When installing a chimney that is higher 
than twelve feet, guide lines must be used. 

• 

  This unit must never be pressurized.  

 

Do not use an automatic stoker with this unit. 

 

Risk of Fire: Do not operate with fuel loading and/or ash 
removal doors open. Do not store fuel or other combustible 
materials within marked installation clearances. Inspect and 
clean flues and chimney regularly. 

CAUTION!!!

 

 

• 

  Hot Surfaces: Keep children away. Do not touch during 

operation. 

• 

  Do not start or operate furnace without checking heating fluid. 

• 

  Check for buried cables and utility lines before digging trench. 

• 

  For safety and proper temperature control, keep fuel door 

closed tightly during operation. 

• 

  Do not fire up furnace until filled with water. 

• 

  Do not to start the unit during a prolonged power failure. 

• 

  Load fuel carefully to avoid injury to hands, fingers and other 

body parts that 

may come in contact with the unit’s loading 

door opening. 

• 

  Cleaning of the heat exchanger, flue pipe, chimney and draft 

inducer if used, is especially important at the end of the 
heating season to minimize corrosion during the summer 
months caused by accumulated ash. 

• 

  When installing the heat exchanger, be sure none of the 

existing system safety controls are disabled. 

• 

  When installing heat exchangers do not tamper with existing 

controls. Wiring to existing blower can be done with a line 
voltage or low voltage thermostat. 

SAFETY INSTRUCTIONS & PRECAUTIONS

 

DANGER!!! 

Do not start fire with chemicals, volatile fluids, rubber, plastics or garbage. Only competent persons 

with a sound understanding of this heating method should operate this furnace. Improper firing could result in 
personal injury and/or damage to unit, and void warranty. 

Do not burn garbage, gasoline, drain oil, naphtha, 

engine oil, railroad ties, particle board, leaves, cardboard, or any other flammable liquids. 

9

Summary of Contents for Crown Royal Stoves Multi-Pass 7200MP





















































Reviews: