background image

 

GTD-LYS011764 (CW/WW) User Manual 

© 2017  GTD

  all  rights  reserved.  Information,  specifications,  diagrams,  images,  and  instructions  herein  are  subject  to 

change without  notice. GTD  logo  and  identifying  product  names  and numbers  herein  are  trademarks  of GTD. Copyright 
protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or 
judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of 

their  respective  companies  and  are  hereby  acknowledged.  All  non-GTD  brands  and  product  names  are  trademarks  or 
registered trademarks of their respective companies. 

GTD  and  all  affiliated  companies  hereby  disclaim  any  and  all  liabilities  for  property,  equipment,  building,  and  electrical 
damages,  injuries  to  any  persons,  and  direct  or  indirect  economic  loss  associated  with  the  use  or  reliance  of  any 

information  contained  within  this  document,  and/or  as  a  result  of  the  improper,  unsafe,  insufficient  and  negligent 

assembly, installation, rigging, and operation of this product. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Guangzhou GTD Lighting Technology Co., Ltd. | 27 Fu Yuan Yi Road, Guangzhou 510805, P.R.China 

+86-20-61808296 | +86-20-61812282 fax | 

www.gtd-lighting.com

 | 

[email protected]

 

Summary of Contents for GTD-LYS011764

















Reviews: