GTD GTD-LYS011764 User Manual Download Page 11

Page: 11 / 16

GTD-LYS011764 (CW/WW) User Manual

Physical / Installation



Weight: 10kg (22lbs.)



IP rating: IP20



Material: Aluminum, steel, plastic



Mounting points: 12mm holes for G-Clamp



Minimum distance to combustible materials: 1.64ft. (0.5m)



Minimum distance to illuminated surfaces: 3.28ft. (1m)

Dynamic effects



Pan/Tilt movement: Manually adjustable



Dimmer: 0-100%, 16-bit, electronic linear dimming

Thermal



Operating range: 14˚F to 113˚F (-10˚C to +45˚C)



Startup range: 5˚F to 113˚F (-15˚C to +45˚C)



Storage range: -40˚F to 140˚F (-40˚C to +60˚C)



Cooling: Passive



Humidity:

≤

85%

Connections



AC power: Neutrik powerCon



DMX data input/output: Chassis 5-pin Neutrik XLR (in/out)

Certification and Safety



EMC: EN 55103-1:2009, EN 55103-2:2009, EN 61000-3-2:2006+A2:2009, EN 61000-3-3:2013



Safety: EN 60598-2-17:1989/A2:1991

Photometric

LYS011764CW:

Summary of Contents for GTD-LYS011764

















Search results

Summary of Contents for GTD-LYS011764

Reviews:

Related manuals for GTD-LYS011764

Brands by name

Popular brands

GTD GTD-LYS011764, User Manual

Search results

Summary of Contents for GTD-LYS011764

Reviews:

Related manuals for GTD-LYS011764

Brands by name

Popular brands