GT GT-1000 User Manual Download Page 20

Page: 20 / 20

www.globetechinnovations.com

The door can

open

fails

close.

1. Infrared beam is

obstructed.

Infrared

sensor

function is enabling, but

the sensor has not been

installed.

1. Remove obstructions.

2. Make sure the infrared

sensor function is disabling.

Remote

transmitter does

not work.

1. Battery level may be

low

2. Transmitter code is

lost

1. Replace the battery

inside the transmitter.

Reprogram

the

transmitter.

The transmitter

operating

distance is too

short.

Battery level may be

low.

Replace battery.

11. Packing list

After receiving the gate operator, you should make an

unpack-inspection, in which you should check whether the product

was damaged. If you have any problem please contact our dealer.

You should find the following items in our standard packing:

No.

Item

Quantity

(GT-600,1000,1500,2000)

sliding gate operator

Transmitter

Release key

User

’s manual

Summary of Contents for GT-1000





















Search results

Summary of Contents for GT-1000

Reviews:

Related manuals for GT-1000

Brands by name

Popular brands

GT GT-1000, User Manual

Search results

Summary of Contents for GT-1000

Reviews:

Related manuals for GT-1000

Brands by name

Popular brands