manualshive.com logo in svg

GSS CozIR-Blink, User Manual

Share
Download
GSS CozIR-Blink User Manual Download Page 8

USER GUIDE

 

Gas Sensing Solutions Ltd. 

Revision 1.2, 29 March 2021 

 

 

Page | 8     For regular updates, sign up at https://gassensing.co.uk 

Copyright © 2021 Gas Sensing Solutions Ltd. 

 

STANDALONE OPERATION 

The sensor can be completely isolated from the rest of the evaluation board electronics.  This allows 
the user to conveniently control the sensor directly via edge connectors J3, J4 and J5.  To operate in 
this manner, the DIP switches (S5) must be set to isolate the sensor from the microcontroller by 
putting them into the off position.   

 

 

Figure 4: DIP Switches (S5, shown in OFF position) 

 
The evaluation board is shipped with the DIP switches set 

ON

 (see label on switch) to connect the 

sensor to the on-board microcontroller by default.   To isolate the sensor from the on-board 
microcontroller, set the switches to 

OFF. 

  Power supply connections to the sensor are described in 

the following section.   
 
The sensor switch connections on the DIP switches are listed below. 

 

SWITCH POSITION 

NAME

 

TYPE

 

DESCRIPTION

 

1 

Rx_In

 

Digital Input

 

UART Receive Input

 

2 

Tx_Out

 

Digital Output

 

UART Transmit Output 

 

3 

NC

 

Unused

 

Do not connect (For internal use only)

 

4 

VDD1

 

Supply

 

Sensor supply voltage

 

5 

NC

 

Unused

 

Do not connect

 

6 

READY

 

Digital Output

 

Data ready pin.  Pulsed high when data 
ready

 

7 

I2C_SDA

 

Digital Input/Output

 

I

2

C serial data input/output.  Pull-up 

resistor to VDD is provided on the 
evaluation board.

 

8 

I2C_SCL

 

Digital Input

 

I

2

C serial clock input. Pull-up resistor to 

VDD is provided on the evaluation 
board.

 

9 

I2C_ENABLE

 

Digital Input

 

Set low for I

2

C interface mode.  Leave 

floating to select UART interface mode.  
Pin status detected at power on.

 

10 

NC

 

Unused

 

Do not connect 

 

 

 

Summary of Contents for CozIR-Blink








































Reviews:

No comments

Brands by name

Popular brands

Load more brands