GSL electronics MPPT10HV Operating Instructions Manual Download

Page: 1 / 8

MPPT10HV R3

Page 1 of 8

Model:

MPPT10HV

Unit 2, 110 Station Road, Seven Hills ,NSW, 2147, Australia

400W Solar Charger

Maximum Power Point Tracker

Operating Instructions

Please read these instructions before use

This revolutionary maximum power point tracker solar charger

was designed using the technology that won GSL Electronics the

prestigious “2008 EDN Innovation award”. A simple, compact and

low cost alternative. Ideal for charging batteries with the new low

cost high efficiency grid type panels.

MPPT10HV Unit

MPPT10HV Specifications

Efficiency Typical

96%

Input Voltage

15V to 90V

Float Voltage

(Maintanence)

Lead Acid - 13.5V / 27V / 54V

LiFePO

- 14V / 28V / 56V

Charge Voltage

14.6V / 29.2V / 58.4V

Max Panel Power

400W on 48V Battery / 200W on 24V Battery

150W on 12V Battery

Quiescent Current

0.04A

Thermal Protection

Multilevel type

Dimensions (mm)

35 X 75 X 143mm

Indications

LED – Battery OK / LOW

PATENT APPLIED FOR - 2010901565

Summary of Contents for MPPT10HV









Search results

Summary of Contents for MPPT10HV

Reviews:

Related manuals for MPPT10HV

Brands by name

Popular brands

GSL electronics MPPT10HV, Operating Instructions Manual

Search results

Summary of Contents for MPPT10HV

Reviews:

Related manuals for MPPT10HV

Brands by name

Popular brands