background image

 

8

 
Attention 

 

Remove exhausted batteries immediately from the unit! 

 

 If the unit is not to be used for longer periods, remove 

batteries even if they are new! 

No responsibility can be accepted for damage due to 
leaking batteries. 

Note on environmental protection 
Do not throw exhausted batteries in the houshold waste ! 
Hand over the old batteries to your radio dealer or a public 

collecting point when buying new ones. 

 

Data Protection 

(Mains and Battery Operation) 

 

When the power supply is disconnected, the time and  the 
last station memory are retained for approx. 5 minutes. 

Reset Button 

If, due to external interferences (caused by static charges 
of carpets, thunderstorms, etc.), the control electronics of 
your Yacht Boy 500 should receive wrong information sig-
nals, or if no entries at all are possible, then press the Reset 
button. 
This is to be found behind the top right opening in the de-

corative speaker grill. 
For pushing the switch, it is best to use a bent-up paper clip. 
By releasing the Reset impulse, the unit is reset to its initial 
programming state. 

The contents of the individual station memory locations are not 

affected. 

However the time setting and the contents of the last station 
memory will be cleared. 
The stored stations and menu options will not be lost neither by a 
power supply failure nor by a Reset. 
 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

Summary of Contents for YB500






























Reviews: