Grundig MASQ RRCD 9100 PLL User Manual Download Page 22

ENGLISH

43

Rectifying minor problems

If a fault occurs, first refer to this information before you take the device for
repair.

If you are unable to rectify the fault using the information given here, contact
your local dealer or service specialist.

Under no circumstances should you attempt to repair the radio recorder
yourself, as this would invalidate the guarantee.

INFORMATION

________________________________

PROBLEM

GENERAL

No sound

The radio recorder
does not respond
when you press the
buttons

TUNER

Poor radio reception

CD

Playback will not start

The CD player skips
tracks

TAPE

Poor cassette play-
back sound quality

No cassette recording

POSSIBLE CAUSE

The volume setting is too low
The headphones are connected
The batteries are flat 
The batteries are incorrectly
inserted 
The mains cable is incorrectly
connected

Static electrical discharge

Weak radio antenna signal

Interference from electrical
devices such as televisions,
video recorders, computers,
neon lamps, thermostats 
or motors.

The CD is damaged or dirty 

A stored track memory is being
played
The RANDOM function is acti-
vated

Dust and dirt on magnetic
heads, capstans or idlers

Recording protection tab 
has been broken off

REMEDY

Turn up the volume
Unplug the headphones 
Replace the batteries
Insert the batteries correctly 
Connect the mains cable
properly

Switch off the radio
recorder, disconnect the
mains cable 
and plug it in again after a
few seconds
Remove any batteries

VHF (FM): tilt and turn the
telescopicantenna
Switch from stereo to mono
reception 
MW and LW: turn the whole
device
Keep the radio recorder
away from electrical
devices

Replace or clean the CD

Switch to normal playback
or delete
Switch off the RANDOM
function

Clean the magnetic heads,
capstan and idler 

Cover the opening with
adhesive tape

Summary of Contents for MASQ RRCD 9100 PLL
























Reviews: