PA 6
Allgemeiner Teil / General Section
GRUNDIG Service
1 - 33
ENGLISH
45
CASSETTE MODE
________________________________________________________________________
Recording
Activate Dolby Noise Reduction if required.
The setting procedure is described in the ”Noise reduction system (Dolby NR)”
section on Page 41.
1
Insert a cassette with the protection tabs intact into the cassette compartment,
select the running direction of the cassette with »
z t
« and search for the
desired position on the cassette with either »
9
« or »
8
«.
2
Select the input source from which you want to record by pressing »
CD
«,
»
TUNER
« or »
AUX
«.
3
Start recording by keeping »
RECORD
« pressed for a short moment.
– The display shows: »
)
«, and recording begins.
Note:
If you are using a cassette on which the protection tabs are removed,
recording is not possible and the display shows the message »
CASS
«. The
cassette compartment opens.
4
To stop recording, press »
5
«.
1050
tuner
105 1
CASS
46
Recording a CD on to cassette (CD COPY)
You can start the recording process from CD on to cassette by pressing only
one button.
Individual tracks of a CD or music programme can be distributed on
both sides of the cassette in this manner, so that long, empty passages at the end
of a cassette are avoided.
1
Insert the cassette into the cassette compartment and put a CD into the CD
compartment.
2
Wind the cassette to the desired point.
3
Select the desired track on the CD.
4
Start the recording by pressing the »
CD-COPY
« button and briefly holding
it down.
– Recording starts. The CD player will begin playback after about four
seconds.
Note:
If you begin recording at the start of the cassette, the HiFi will play the lead-
in tape for about six seconds. Playback of the CD is then automatically
started.
During recording, the only buttons that can be used are »
5
«, »
DISC
OPEN/CLOSE
« or »
TAPE OPEN/CLOSE
«. All other functions are
blocked.
If playback of the CD is stopped, recording stops as well.
If one side of the cassette is full, CD playback is set to pause.
If the Reverse function is selected, recording is automatically continued on the
second side of the cassette.
CASSETTE MODE
________________________________________________________________________
48
INFORMATION
__________________________________________________________________________
Rectifying minor problems
Not every kind of sound interference is caused by a defect in your HiFi system. Impairment
can also be caused by leads having been accidentally pulled out, damaged CDs and worn
out batteries in the remote control. If the following measures do not bring about
satisfactory results, consult an authorised dealer.
GENERAL PROBLEMS
Problem
The HiFi switches itself off.
The HiFi does not function.
No output signal.
The left and right channels are inverted.
Bass sound missing.
The remote control is not functioning.
RADIO RECEPTION
Problem
No output signal.
Loud noise interference.
The reception signal is weak.
Possible cause/remedy
The transformer could be overheated. Switch of the HiFi
and remove all objects that could possibly cover the air
vents on the rear side of the HiFi and let it cool down for
approximately 15 minutes before you switch it on again.
Problems due to electrostatic discharge. Switch the HiFi
off and on again using the
POWER
button or pull out
the mains plug and then plug it in again.
Increase the volume (+). Disconnect the headphones.
Check the connection to the loudspeaker module. Make
sure the MUTING function is not activated.
Check the connection to the loudspeaker module.
Check the connection to the loudspeaker module.
Change batteries.
Wrong angle or distance to the device too great.
Possible Cause/Remedy
The MUTING function is activated due to poor stereo
reception. Select FM MONO or correct the frequency
manually.
Adjust the antenna.
Connect an external antenna for better reception.
ENGLISH
49
RECTIFYING MINOR PROBLEMS
____________________________________________
General instructions for laser devices
You will find a similar sign to the one shown here on the bottom of the unit.
CLASS 1 LASER PRODUCT means that the laser is designed in such a way as to
ensure that the maximum permissible emission value cannot be exceeded under
any circumstances.
Caution:
If operation devices or methods other than those specified here are
employed, it may lead to dangerous exposure to emissions.
CLASS 1
LASER PRODUCT
CD MODE
PROBLEM
The CD compartment does not close.
Playback is not functioning.
”NO DISC” appears in the display.
Playback does not begin with the first
track.
The system does not function.
Possible cause/remedy
CD not inserted correctly.
The CD is dirty, scratched or upside down. A sudden
temperature change has caused condensation on the
laser lens system.
This will dry off by itself after a short time.
No CD has been inserted, the CD is dirty, scratched or
warped. Try another disc.
PROGRAMME or SHUFFLE mode is activated. Press
5
and then
4
PAUSE
.
Press
5
, then
CANCEL
and then
4
PAUSE
.