GRUNDIG Service
1 - 9
M 100-T
Allgemeiner Teil / General Section
Front of the tuner
POWER
This button is used for switching the tuner on and off.
TUNING
Q R
You use these buttons to start the station search (AUTO TUNING) or to
advance the frequency step by step (MANUAL TUNING). If you keep the
button depressed, station search is accelerated.
STATION
1 2
These buttons are used to scroll through the station memory in ascending (>) or
descending (<) order.
MEMORY
This button stores the actual station at the lowest empty memory location.
When pressing this button longer, the AUTO STORE function will be started.
CANCEL
This button is used to delete individual memory locations or, if desired, the
entire memory contents (by keeping the button depressed for more than 10 seconds).
BAND
This button is used to switch to the
FM ANTENNA
,
FM CABLE
and
MW
bands.
IF/MONO
Pressing this button repeatedly switches the FM reception mode to STEREO WIDE
➧
STEREO NARROW
➧
MONO WIDE
➧
MONO NARROW
➧
STEREO WIDE
➧
etc.
OPERATING ELEMENTS
DISPLAY
1
MUTING
– This indicates that the MUTING
function is active.
2
MONO
– This comes on if the MONO function
is activated.
3
STEREO
– This indicates that the tuner is
receiving FM stereo broadcasts
4
AUTO
– This indicates that the AUTO TUNING
function is active
5
Signal strength
– The more dashes you can see,
the stronger the reception of the station you have
tuned to.
6
– Shows the chosen FM IF bandwidth
(NARROW/WIDE) and the triangle
lights up if the unit is exactly tuned to a station.
7
ANTENNA
– comes on when the antenna
attenuator is switched off (FM ANTENNA).
8
CABLE
– comes on during broadband cable
reception if the antenna attenuator is switched on
(FM CABLE).
9
Station number
seven-segment display – This
shows the number of the selected memory
location (1 to 59)
0
14-segment display
– for (RDS) station name,
frequency, radiotext, RDS time, selected
programme type or messages.
MUTING MONO STEREO AUTO
ANTENNACABLE
########
MHz
1
2
3
4
5
6
7
0
8
kHz
9
by
by
POWER
POWER
M100-T
M100-T
MEMORY
BAND
IF/MONO
MEMORY
BAND
CANCEL
CANCEL
IF/MONO
STATION
STATION
TUNING
TUNING
TUNING
TUNING
1
2
2
MUTING
MONO
STEREO
AUTO
ANTENNA
CABLE
########
MHz
MEMORY
CANCEL
TUNING
STATION
TUNING
POWER
BAND
IF/MONO
5
6
1
2
1
OPERATION
Selecting the wave band
• Select the desired wave band (FM ANTENNA,
FM CABLE or MW) by pressing
BAND
.
• Pressing this button switches to the next wave
band in the following order:
FM ANTENNA- FM
CABLE - MW - FM ANTENNA
– The display shows the selected band.
If you receive broadcasts via broad band cable
of a public or private cable service, there may
be high signal inputs at your antenna terminal,
which may in turn cause reception disturbances.
• If this is the case, select
FM CABLE
to switch on
the input attenuator. This reduces the antenna
input sensitivity, thus reducing disturbances. This
setting is automatically stored after 5 seconds.
FM reception
WIDE/NARROW, STEREO/MONO
The FM reception mode is automatically set to stereo
and wide every time automatic tuning is started.
Still, there are stations with disturbances or noise
in the audio signal, due to weak signal or inter-
ference of adjacent (neighbour) stations.
The
IF/MONO
button provides a step-by-step pro-
gressive attenuation of those disturbances or noise.
• When the FM reception is disturbed, press
IF/MONO
. The reception mode switches to
‘STEREO NARROW’
thus avoiding
interference from strong neighbour stations.
• If stereo narrow reception still exhibits too much
disturbing noise press
IF/MONO
again to
select ‘MONO WIDE’. Now the mono function
will reduce noise due to weak reception.
• It is unlikely that you still hear noise but a last
step is to select ‘MONO NARROW’ by pressing
IF/MONO
again. You have now selected the
highest noise disturbance reduction both for neigh-
bour station interference and for weak reception
➥
➥
➥
MUTING
STEREO
ANTENNA
FM 9350
MHz
MUTING
STEREO
ANTENNA
FM 9350
MHz
MONO
ANTENNA
FM 9350
MHz
MONO
ANTENNA
FM 9350
MHz
➥
MUTING
ANTENNA
FM 8750
MHz
MUTING
CABLE
FM 8750
MHz
➥
MW
528
kHz
➥
➥
LANGUAGE SELECTION
Language selection
You can call up the programme type display in
the following languages: english, german,
french, portuguese, spanish, italian, dutch, and
swedish.
• Keep the
IF/MONO
button pressed while the
unit is turned off, and then turn on the tuner.
– The current language appears in the display.
• By using the
STATION
1 2
buttons you can
call up the desired language.
• Store your selection by pressing the
MEMORY
button.
➥
ENGLISH
DEUTSCH
