background image

English (GB)

3

English (GB) Installation and operating instructions

Original installation and operating instructions.

CONTENTS

Page

1. Symbols used in this document

2. Scope of supply

Grundfos PM Rain unit.

Grundfos PM Rain unit and SB pump.

Grundfos PM Rain unit and JP pump.
Supplied with an automatic air release valve 
fitted in the priming hole and unions.

1.

Symbols used in this document

3

2.

Scope of supply

3

3.

Applications

4

3.1

Liquids

4

3.2

Temperatures

4

3.3

Operating pressure

4

4.

Installation

4

4.1

Connections

4

4.2

Mechanical installation

5

4.3

Location

5

4.4

Pressure settings

6

4.5

Electrical installation

7

4.6

Connecting units with cable and plug 
fitted

7

4.7

Alternative power supply

7

5.

Control panel

7

5.1

DIP switches

8

5.2

Enabling the DIP switch settings

8

6.

Start-up

9

7.

Operation

9

7.1

Operating principle

9

7.2

Start/stop according to water 
consumption

10

7.3

Start/stop with 1 bar (100 kPa) 
differential pressure

10

8.

Functions

10

8.1

Anti-cycling

10

8.2

Dry-running protection

10

9.

Frost protection

11

10.

List of warnings

12

11.

Technical data

12

12.

Fault finding

13

13.

Further product information

14

14.

Disposal

14

Warning

Prior to installation, read these 
installation and operating instructions. 
Installation and operation must comply 
with local regulations and accepted 
codes of good practice.

Warning

The use of this product requires 
experience with and knowledge of the 
product.
Persons with reduced physical, 
sensory or mental capabilities must not 
use this product, unless they are under 
supervision or have been instructed in 
the use of the product by a person 
responsible for their safety.
Children must not use or play with this 
product.

Warning

If these safety instructions are not 
observed, it may result in personal 
injury.

Warning

If these instructions are not observed, 
it may lead to electric shock with 
consequent risk of serious personal 
injury or death.

Caution

If these safety instructions are not 
observed, it may result in malfunction 
or damage to the equipment.

Note

Notes or instructions that make the job 
easier and ensure safe operation.

Summary of Contents for PM Rain





















Reviews: