background image

English (GB)

11

8.2.3 Resetting of dry-running warning

Manual resetting

If a dry-running warning has been activated, the 
pump can be restarted manually by pressing [Reset]. 
If the unit detects no pressure and no flow within 
40 seconds after restarting, the dry-running warning 
is re-activated. 

Auto-reset

When the auto-reset function is enabled, the pump 
will be restarted automatically after 24 hours in 
warning condition. If, after restarting, the pump has 
not been primed within 3 minutes of operation, the 
dry-running warning will reappear. The auto-reset 
function will attempt to restart the pump after 
24 hours. This will be repeated for five days, and if 
rainwater is still not available, there will be one week 
between the restarting attempts.

8.2.4 Power supply failure 

In case of a power supply failure, the pump restarts 
automatically when power returns and runs for at 
least 10 seconds.

9. Frost protection

If the unit is subjected to frost in periods of inactivity, 
the unit and the piping system should be drained 
before the unit is taken out of operation.

Note

The unit has no built-in draining 
options.

Summary of Contents for PM Rain





















Reviews: