background image

En
gl

is

h (
G

B)

24

10. Technical data

10.1 Operating conditions

10.1.1 Operating mode

The pumps are designed for intermittent operation 
(S3). When completely submerged in the pumped 
liquid, the pumps can also operate continuously 
(S1). 

10.1.2 Installation depth 

Maximum 10 m below liquid level.

10.1.3 Operating pressure

Maximum 6 bar.

10.1.4 Number of starts per hour

Maximum 30.

10.1.5 pH value

Pumps in permanent installations can be used for 
pumping liquids with a pH value between 4 and 10.

10.1.6 Liquid temperature

0-40 °C. 
For short periods of maximum 10 minutes, a 
temperature of up to 60 °C is allowed. This applies 
for standard versions only.

10.1.7 Density of pumped liquid

When pumping liquids with a density and/or a 
kinematic viscosity higher than that of water, use 
motors with correspondingly higher outputs.

10.1.8 Sound pressure level

The sound pressure level of the pumps is lower than 
the limiting values stated in the EC Council Directive 
2006/42/EC relating to machinery.

10.2 Electrical data

10.2.1 Power supply

1 x 230 V - 10 %/+ 6 %, 50 Hz

3 x 400 V - 10 %/+ 10 %, 50 Hz

10.2.2 Enclosure class

IP68, according to IEC 60529.

10.2.3 Insulation class

F (155 °C).

10.2.4 Pump curves

Pump curves are available via www.grundfos.com.
The curves are to be considered as a guide. They 
must not be used as guarantee curves.
Test curves for the supplied pump are available on 
request.

10.3 Dimensions and weights

10.3.1 Dimensions

See figs 

1

 to 

3

 in 

Appendix

.

10.3.2 Weights

Weights do not include accessories.

11. Disposing of the product

This product or parts of it must be disposed of in an 
environmentally sound way:
1. Use the public or private waste collection service.
2. If this is not possible, contact the nearest 

Grundfos company or service workshop.

The crossed-out wheelie bin symbol on 
a product means that it must be 
disposed of separately from household 
waste. When a product marked with this 
symbol reaches its end of life, take it to a 
collection point designated by the local 

waste disposal authorities. The separate collection 
and recycling of such products will help protect the 
environment and human health.
See also end-of-life information at 
www.grundfos.com/product-recycling.

Explosion-proof pumps must never pump 
liquids at a temperature higher than 40 °C.

Power [kW]

Weight [kg]

DP 0.9 - 1.5

39

DP 2.6

68

EF 0.6 - 1.5

39

Summary of Contents for DP AUTOADAPT Series



















































Reviews: