background image

When you need to select any of these countries, you can Double knock to 
enter the next interface. Here we select Italy as an example, as Fig 2-5-3.

C

Fig 2-5-3

When the country arrives at Italy, Double knock to enter the two options 
‘YES’ and ‘NO’, and the cursor stays at ‘NO’ in default, as Fig 2-5-4.

D

Fig 2-5-4

E

Fig 2-5-5

Single knock to select ‘YES’, as Fig 2-5-5. 

F

Double knock to confirm your selection, LCD will display ‘Select OK’ with 
the country name in the below, as Fig 2-5-6. 

Note: 

if you still single knock at the interface as Fig 2-5-5, the cursor will 

go to ‘NO’ again as Fig 2-5-4, then if you double knock, the display will 
switch to the interface as Fig 2-5-3.

Fig 2-5-6

G

Note:

  If  you  have  selected  and  confirmed  an  unwanted  country 

neglectful, please contact Growatt for specific software to clear and reset 
again.

When the selection is successful, the inverter will reboot automatically.

2.5.2 Commissioning

After  the  inverter  reboot,  LCD  will  produce  the  following  messages  in  order: 
‘Ser  NO:  xxx’->’xxxxx’->’FW  version’->’Waiting’->’No  AC  connection’,  the 
display repeats ’NO Utility’ and LED will be red.

Close  the  AC  breaker  or  fuse  between  PV-Inverter  and  grid.  Turn  on  the  DC 
switch. The normal operating sequence begins.

Under normal operating conditions the LCD displays ‘Power: xxx.x W’. That is 
the power fed to the grid. The LED turns green.

This completes the check.

2.6 System diagram

A
B

PV Panel: Provide DC power to inverter.

Converts DC (Direct Current) power from PV panel (s) to AC (Alternating 
Current) power. Because Inverter is grid-connected it controls the current 
amplitude according to the PV Panel power supply. Inverter always tries to 
convert the maximum power from your PV panel(s).

9

8

Summary of Contents for Grid













Reviews: