background image

6

5

When  installing  or  using  a  battery  system,  the  safety  information  contained  in  this 
section must always be followed. For safety reasons, it is the installer's responsibility to 
be familiar with this manual and all warnings before installation.

2.1 Basic security

The battery system has been designed and tested in accordance with strict rules with 
international safety certification requirements. Before any installation or use of the 
battery system, please read all safety instructions carefully and always follow the relevant 
rules. Growatt is not responsible for any consequences resulting from violation of the 
following regulations:

Ÿ

Damage occurred during transportation.

Ÿ

Incorrect transportation, storage, installation and use, or customer fails to convey the 

correct information about transportation, storage, installation and use to terminal 
customers. 

Ÿ

Non-professional installation.

Ÿ

Failure to obey the rules of this operation instructions and safety precautions in this 

document.

Ÿ

Unauthorized modifications or removal of the software package.

Ÿ

The product's tamper label is damaged or the product lacks any parts (except 

authorized disassembly parts).

Ÿ

Operation in extreme environments which are not allowed in this document.

Ÿ

Repair, disassemble, or change PACKs without authorization and cause failure.

Ÿ

 Damage to shell labels or modifies date of production. 

Ÿ

Battery packs fail to be charge for more than six months. 

Ÿ

Damages due to force majeure (such as lightning, earthquakes, fire, and storms).

Ÿ

Warranty expiration.

2.2 Safety Precautions

2.2.1 Environmental requirements

Ø

Do not expose the battery to temperature above 50

℃ 

or heat sources.

Ø

Do not install or use the battery in wet locations, moisture, corrosive gases or liquids, 

such as bathroom. 

Ø

 Do not expose the battery to direct sunlight for extended periods of time.  

Ø

Place battery in safe place away from children and animals.

Ø

Battery power terminals shall not touch conductive objects such as wires. 

Ø

Do not dispose the batteries in fire, which may cause an explosion.

Ø

The battery system shall not come in contact with liquids.

 

Safety 

2.2.2 Operation Precautions

Ø

Do not touch the battery system with wet hands.

Ø

Do not disassemble the battery system without permission.

Ø

Do not crush, drop or pierce the battery pack and high voltage controller.

Ø

Dispose the batteries according to local safety regulations.

Ø

Store and recharge battery in accordance with this manual.

Ø

Ensure the connection of ground wire reliable.

Ø

Remove all metal objects such as watches and rings that could cause a short-circuit 

before installation, replacement and maintenance.

Ø

The system should be installed, repaired, replaced or maintained by skilled person or 

instructed person

ª

Skilled person  

        Person with relevant education and experience to enable him or her to perceive risks
        and to avoid hazards which the equipment can create .
        Note 1 to entry: Such person has access to restricted access areas
        [SOURCE: IEC 60050-195:1998, 195-04-01, Modified – The word “(electrically)” 
        has been deleted from the term, and “electricity” has been replaced by “the 
        equipment” in the definition. The note has been added.]   

ª

Instructed person

        Person adequately advised or supervised by skilled persons to enable him or her to 
        perceive risks and to avoid hazards which the equipment can create
        Note 1 to entry: Such person has access to restricted access areas 
        Note 2 to entry: Examples of activities performed by an instructed person can be 
        found in IEC 61140:2001, Clause 8.
        [SOURCE: IEC 60050-195:1998, 195-04-02, Modified – The word “(electrically)”   
        has been deleted from the term, and the notes have been added.]

Ø

When storing or handling batteries, do not stack batteries without package.

Ø

Do not broke the battery, the released electrolyte may be toxic and is harmful to skin 

and eyes.

Ø

Packaged batteries should not be stacked more than specified number stipulated on 

the packing case.

Ø

Do not use damaged, failed or deformed batteries, which may lead to high 

temperature or even dangerous accidents. Continued operation of damaged battery may 
result in electrical shock, fire or even worse. 

2.3 Warning Labels

Symbols

Description

Operation after 5 minutes after disconnecting the power supply 
(including disconnect/connect power wiring)

Do not dispose in trash

Lithium ion battery can be recycled

Certification in European union area

Electric shock hazard

Summary of Contents for ARK 5.1-25.6XH-A1




















Reviews: