background image

Residual I High

Leakage current
too high

1.Restart inverter.
2.If error message still exists,
contact Growatt.

PV Voltage High

The DC input
voltage is exceeding
the maximum tolerable
value.

Disconnect the DC switch
immediately.

Auto Test Failed

Auto test didn't passed.

Restart inverter

Information

If the suggestions do not work, please connect to the Growatt.

10.2 Errors(E)

Errors(E) codes identify a possible equipment failure, fault or incorrect inverter
setting or configuration. Any and all attempts to correct or clear a fault must be
performed by qualified personnel. Typically, the (E) code can be cleared once the
cause or fault is removed. Some of the (E) codes, Error as indicated in the table
below, may indicate a fatal error and require you to contact the supplier or the
Growatt to replace a new one.

Error code

Description

Suggestion

Error: 101

Communication fault Slave
processor can't receive data
from Master processor.

1.Restart inverter
2.If error message still exists,
contact Growatt.

Error: 102

Consistent fault. Data
received by Master and Slave
processor are different. The
reason can be utility grid
voltage or frequency change

frequently.  .

1.Restart inverter.
2.If error message appears
frequently or error message
still exists after replacement,

check utility grid. If you require

help, contact Growatt.
3.If error message still exists,
contact Growatt.

Error: 116

EEPROM fault

Contact Growatt.

Error: 117

Relay fault

Contact Growatt.

Error: 118

Init model fault

Contact Growatt.

Error: 119

GFCI Device Damage

Contact Growatt.

Error: 120

HCT fault

Contact Growatt.

Error: 121

Communication fault.
Master processor can't
receive data from Slave
processor.

1.Restart the inverter
2.If error message still exists,
contact Growatt..

Error: 122

Bus voltage fault

Contact Growatt.

56

57

Summary of Contents for 2500MTL







































Reviews: