background image

OM-TA/3         3

WARNING:   THE MIXER MUST BE INSTALLED BY PERSONNEL WHO ARE QUALIFIED TO WORK WITH 

ELECTRICITY, IMPROPER INSTALLATION CAN RESULT IN INJURY TO PERSONNEL AND/OR DAMAGE 

TO EQUIPMENT.

WARNING:   ANY MECHANICAL OR ELECTRICAL CHANGE MUST BE APPROVED BY THE GROEN FOOD SERVICE 

ENGINEERING DEPARTMENT.

WARNING:   TURN OFF AGITATOR BEFORE ADDING INGREDIENTS OR INSPECTING KETTLE CONTENTS. DO NOT 

WEAR LOOSE CLOTHING OR JEWELRY AROUND OPERATING MIXER KETTLE. KEEP WELL CLEAR OF 

ROTATING MIXER ARMS AND PADDLES AT ALL TIMES.

WARNING:   THE UNIT IS EQUIPPED WITH AN AUTOMATIC CUTOFF SWITCH. IF POWER IS ON WHEN A TILTED 

MIXER IS LOWERED INTO THE OPERATING POSITION, THE MIXER WILL AUTOMATICALLY START.

CAUTION:   STARTING WITH THE MIXER SET AT HIGH SPEED MAY CAUSE MATERIAL TO SPILL OUT OF THE 

KETTLE ON TWO SPEED AND VARIABLE SPEED UNITS.

CAUTION:   UNDER HEAVY LOAD DO NOT RUN THE MIXER CONTINUOUSLY AT SLOWER THAN 5% OF FULL 

SPEED. SLOWER OPERATION COULD DAMAGE THE SPEED CONTROL.

WARNING:   BEFORE CLEANING ANY PART OF THE MIXER, OTHER THAN THE AGITATOR, DISCONNECT THE 

ELECTRICAL SUPPLY AT THE CIRCUIT BREAKER OR FUSE BOX TO AVOID POSSIBLE ELECTRICAL 

SHOCK.

WARNING:   KEEP WATER AND SOLUTIONS OUT OF THE CONTROLS, ELECTRICAL WIRING, AND DRIVE 

MECHANISM. NEVER SPRAY OR HOSE THE MIXER.

CAUTION:   WHEN YOU INSTALL THE SCRAPER BLADES, MAKE SURE THE SCRAPER IS CURVED. A REVERSED 

SCRAPER WILL NOT SCRAPE AND CAN CAUSE SERIOUS DAMAGE.

WARNING:   AVOID CONTACT WITH CLEANING PRODUCTS IN ACCORDANCE WITH SUPPLIER AND 

MANUFACTURER RECOMMENDATIONS. MANY CLEANERS ARE HARMFUL TO THE SKIN, EYES, 

MUCOUS MEMBRANES AND CLOTHING. READ THE WARNINGS AND FOLLOW DIRECTIONS ON THE 

CLEANER LABEL.

WARNING:   USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY GROEN OR THEIR 

AUTHORIZED DISTRIBUTOR VOIDS ALL WARRANTIES AND CAN CAUSE BODILY INJURY TO THE 

OPERATOR AND DAMAGE TO THE EQUIPMENT.

WARNING:   SERVICE PERFORMED BY OTHER THAN FACTORY AUTHORIZED PERSONNEL WILL VOID ALL 

WARRANTIES.

WARNING:   BEFORE REPLACING ANY PARTS, SHUT OFF ALL ELECTRIC POWER SUPPLIES TO THE COOKER/

MIXER.

WARNING:   USE ONLY GROEN-SUPPLIED PARTS. SUBSTITUTION OF UNAUTHORIZED OR GENERIC PARTS CAN 

RESULT IN BODILY INJURY TO THE OPERATOR AND DAMAGE TO THE EQUIPMENT.

WARNING:  DO NOT PLACE HANDS, TOOLS, OR HOSES IN KETTLE WHILE AGITATOR IS MOVING.
WARNING:  AGITATOR AREA MUST BE CLEAR OF OBSTRUCTION BEFORE OPERATION. TO RUN AGITATOR: 

 

1)  ENSURE KETTLE IS FULLY UPRIGHT

 

2)  ENSURE MIXER HEAD IS FULLY DOWN AND LATCHED

 

3)  SET THE SPEED DIAL TO DESIRED SPEED

 

4)  TURN THE START SWITCH TO ON

 

TO STOP AGITATOR:

 

1)  PRESS THE RED STOP BUTTON OR TURN THE SWITCH TO OFF

IMPORTANT - READ FIRST - IMPORTANT

Summary of Contents for D - 40/60/80 TA/3





















Reviews: