background image

OM-BPM-15/30/40G(C,A) (CE) INTERNATIONAL

IMPORTANT - READ FIRST - IMPORTANT

IMPORTANT: THESE APPLIANCES MUST BE INSTALLED BY A COMPETENT PERSON IN 

CONFORMITY WITH THE INSTALLATION AND SERVICING INSTRUCTIONS 

AND NATIONAL REGULATIONS IN FORCE AT THE TIME. PARTICULAR 

ATTENTION MUST BE PAID TO THE FOLLOWING (CE):
I. E. E. REGULATIONS FOR ELECTRICAL INSTALLATIONS
ELECTRICITY AT WORK REGULATIONS
GAS SAFETY (INSTALLATION & USE REGULATIONS
HEALTH AND SAFETY AT WORK ACT
FIRE PRECAUTIONS ACT
LOCAL AND NATIONAL BUILDING REGULATIONS

 

  DETAILED RECOMMENDATIONS ARE CONTAINED IN INSTITUTE OF GAS 

ENGINEERS PUBLISHED DOCUMENTS: IGE/UP/1, IGE/UP/2, BS6173 AND 

BS5440 (CE).

 

  THESE APPLIANCES HAVE BEEN CE-MARKED ON THE BASIS OF 

COMPLIANCE WITH THE GAS APPLIANCE DIRECTIVE, EMC AND LOW 

VOLTAGE DIRECTIVE FOR THE COUNTRIES, GAS TYPES AND PRESSURES 

AS STATED ON THE DATA PLATE.

WARNING:  TO PREVENT SHOCKS, ALL APPLIANCES WHETHER GAS OR ELECTRIC, 

MUST BE EARTHED.

 

  ON COMPLETION OF THE INSTALLATION, THESE INSTRUCTIONS SHOULD 

BE LEFT WITH THE ENGINEER-IN-CHARGE FOR REFERENCE DURING 

SERVICING. FURTHER TO THIS, THE USERS INSTRUCTIONS SHOULD 

BE HANDED TO THE USERS AND THE INSTALLER SHOULD INSTRUCT 

THE RESPONSIBLE PERSON(S) IN THE CORRECT OPERATION AND 

MAINTENANCE OF THE APPLIANCE. EMPHASIS SHOULD BE MADE WITH 

REGARD TO SAFE OPERATION OF DRAIN VALVE.

 

  IT IS MOST IMPORTANT THAT THESE INSTRUCTIONS BE CONSULTED 

BEFORE INSTALLING AND COMMISSIONING THE APPLIANCE. FAILURE TO 

COMPLY WITH THE SPECIFIED PROCEDURES MAY RESULT IN DAMAGE OR 

THE NEED FOR A SERVICE CALL.

CAUTION:   SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK WHEN CUT.
WARNING:  DISCONNECT POWER BEFORE SERVICING. FAILURE TO DISCONNECT 

COULD RESULT IN ELECTROCUTION AND DEATH.

CAUTION:   UNIT WEIGHS 470 TO 560 LB. (191 TO 255 KG). FOR SAFE HANDLING, 

INSTALLER SHOULD OBTAIN HELP AS NEEDED, OR EMPLOY APPROPRIATE 

MATERIALS HANDLING EQUIPMENT (SUCH AS A FORKLIFT, DOLLY, OR 

PALLET JACK) TO REMOVE THE UNIT FROM THE SKID AND MOVE IT TO THE 

PLACE OF INSTALLATION.

WARNING:  INSTALLATION OF THE BRAISING PAN MUST BE DONE BY PERSONNEL 

QUALIFIED TO WORK WITH GAS AND ELECTRICITY. IMPROPER 

INSTALLATION CAN RESULT IN INJURY TO PERSONNEL AND/OR DAMAGE 

TO EQUIPMENT.

WARNING:  THIS UNIT IS DESIGNED FOR COMMERCIAL USE. NEVER USE HOME 

OR RESIDENTIAL GRADE GAS CONNECTIONS. THEY DO NOT MEET 

COMMERCIAL GAS CODES AND COULD BE HAZARDOUS.

DANGER:   ELECTRICALLY GROUND THE UNIT AT THE TERMINAL PROVIDED. FAILURE 

TO GROUND UNIT COULD RESULT IN ELECTROCUTION AND DEATH.

WARNING:  KEEP THE APPLIANCE AREA FREE AND CLEAR OF COMBUSTIBLE 

MATERIALS. FAILURE TO DO SO COULD RESULT IN FIRE OR PROPERTY 

DAMAGE.

CAUTION:   BE SURE ALL OPERATORS READ, UNDERSTAND AND FOLLOW THE 

OPERATING INSTRUCTIONS, CAUTIONS AND SAFETY INSTRUCTIONS 

CONTAINED IN THIS MANUAL.

CAUTION:   THE BRAISING PAN IS NOT INTENDED FOR USE AS A DEEP-FAT FRYER. 

SHALLOW-FRYING IS PERMISSIBLE AS LONG AS THE OIL LEVEL DOES 

NOT EXCEED THE HEIGHT MARK ON THE LOWER REAR WALL (2”, 50MM 

MAXIMUM). SEE THE  USER INSTRUCTIONS SECTION FOR SPECIFIC 

DETAILS. 

CAUTION:   KEEP FLOORS IN BRAISING PAN WORK AREA CLEAN AND DRY. IF SPILLS 

OCCUR, CLEAN IMMEDIATELY TO AVOID THE DANGER OF SLIPS OR FALLS.

WARNING:   WHEN TILTING BRAISING PAN FOR PRODUCT TRANSFER:

1) USE CONTAINER DEEP ENOUGH TO CONTAIN AND MINIMIZE PRODUCT 

SPLASHING.
2) PLACE CONTAINER ON STABLE, FLAT SURFACE, AS CLOSE TO PAN AS 

POSSIBLE.
3) STAND TO SIDE OF PAN WHILE POURING — NOT DIRECTLY IN POUR PATH 

OF HOT CONTENTS.
4) RETURN PAN BODY TO LEVEL POSITION AFTER CONTAINER IS FILLED OR 

TRANSFER IS COMPLETE.

5) DO NOT OVERFILL CONTAINER, AVOIDING DIRECT SKIN CONTACT WITH HOT 

CONTAINER AND ITS CONTENTS.

WARNING:   DO NOT HEAT EMPTY PAN FOR MORE THAN 5 MINUTES AT A SETTING HIGHER 

THAN 300ºF (149ºC).

WARNING:   IF THE PAN CONTAINS ITEMS IN HOT LIQUIDS SUCH AS SAUCE OR MELTED FAT, 

THEY CAN SLIDE FORWARD SUDDENLY DURING TILTING AND CAUSE THE HOT 

LIQUID TO SPLASH OUT.

WARNING:  AVOID ALL DIRECT CONTACT WITH HOT FOOD PRODUCT OR WATER IN THE 

PAN. DIRECT CONTACT COULD RESULT IN SEVERE BURNS.

WARNING:  IT IS RECOMMENDED THAT WATER AND SOLUTIONS BE KEPT OUT OF 

CONTROLS AND BURNERS. DO NOT USE HIGH PRESSURE SPRAY OR STEAM 

DIRECTLY ON THE CONTROL CONSOLE, ELECTRICAL CONNECTIONS AND 

BURNERS. 

CAUTION:   MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES, MUCOUS MEMBRANES 

AND CLOTHING. PRECAUTIONS SHOULD BE TAKEN TO WEAR RUBBER GLOVES, 

GOGGLES OR FACE SHIELD AND PROTECTIVE CLOTHING. CAREFULLY READ THE 

WARNINGS AND FOLLOW THE DIRECTIONS ON THE LABEL OF THE CLEANER 

TO BE USED. FAILURE TO DISCONNECT COULD RESULT IN ELECTROCUTION 

AND DEATH.

WARNING:   BEFORE REPLACING ANY PARTS, DISCONNECT THE UNIT FROM THE ELECTRIC 

POWER SUPPLY AND CLOSE THE MAIN GAS COCK. ALLOW FIVE MINUTES FOR 

UNBURNED GAS TO VENT.

CAUTION:   USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY 

AUTHORIZED DISTRIBUTORS CAN CAUSE INJURY TO THE OPERATOR AND 

DAMAGE TO THE EQUIPMENT AND WILL VOID ALL WARRANTIES.

IMPORTANT:  SERVICE PERFORMED BY OTHER THAN GROEN AUTHORIZED SERVICE AGENT 

WILL VOID ALL WARRANTIES.

IMPORTANT: THIS APPLIANCE IS MARKED “CE” ON THE BASIS OF COMPLIANCE WITH EMC AND 

LOW VOLTAGE DIRECTIVE.

WARNING:  THIS UNIT IS INTENDED FOR USE IN THE COMMERCIAL HEATING, COOKING AND 

HOLDING OF WATER AND FOOD PRODUCTS, PER THE INSTRUCTIONS CONTAINED 

IN THIS MANUAL. THIS EQUIPMENT IS NOT FOR CONTINUOUS MASS PRODUCTION 

OF FOOD PRODUCTS OR ANY OTHER USE COULD RESULT IN SERIOUS PERSONAL 

INJURY OR DAMAGE TO THE EQUIPMENT AND WILL VOID WARRANTY.

WARNING:  WHEN OPENING TANGENT DRAW-OFF (TDO) VALVE FOR PRODUCT TRANSFER:
 

  1) USE CONTAINER DEEP ENOUGH TO CONTAIN AND MINIMIZE PRODUCT SPLASHING. 

 

  2) PLACE CONTAINER ON STABLE, FLAT SURFACE, AS CLOSE TO UNIT AS POSSIBLE.

 

  3) DO NOT OVER FILL CONTAINER. AVOID DIRECT SKIN CONTACT WITH HOT 

CONTAINER AND ITS CONTENTS.

CAUTION:  THIS APPLIANCE CAN BE USED BY CHILDREN AGED FROM 8 YEARS AND 

ABOVE AND PERSONS WITH REDUCED PHYSICAL, SENSORY OR MENTAL 

CAPABILITIES OR LACK OF EXPERIENCE AND KNOWLEDGE IF THEY HAVE BEEN 

GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE 

IN A SAFE WAY AND UNDERSTAND THE HAZARDS INVOLVED.

CAUTION:   CHILDREN SUPERVISED ARE NOT TO PLAY WITH THIS APPLIANCE.
CAUTION:  CLEANING AND USER MAINTENANCE SHALL NOT BE MADE BY CHILDREN 

WITHOUT SUPERVISION.

CAUTION:   FOR APPLIANCES INTENDED FOR USE AT ALTITUDES EXCEEDING 2,000 M, THE 

MAXIMUM ALTITUDE WILL BE STATED OR MARKED ON APPLIANCE.

Summary of Contents for BMP-30GC




















Reviews: