Grizzly QUIET Series Owner'S Manual Download

Page: 39 / 40

Model T32335 (Mfd. Since 11/20)

-37-

T32335

DRAIN TANK

AFTER

EVERY USE!

Motor: 1.5 HP, 120V, 1-Ph, 60 Hz

Full-Load Current Rating: 8A

Type/Size: One-Stage, 2-Gallons

Max. Airflow @ 90 PSI: 2.4 SCFM

Cut-Out Pressure: 115 PSI

Cut-In Pressure: 95 PSI

Connection Size: 1/4" NPT

Weight: 48 lbs.

Specifications

WARNING!

Mfd. for Grizzly in China

To reduce the risk of serious injury when using this machine:

1. Read and understand owner’s manual before operating.

2. Always wear ANSI-approved eye protection and any additional personal

protective equipment required by attachment tools.

3. Only plug power cord into a grounded outlet. Do not use with

grounding adapter.

4. DO NOT use this air compressor for breathable air supply.

5. DO NOT touch compressor parts during or immediately following

operation. These parts will be hot.

6. Always disconnect power and drain air tank before moving or

servicing. DO NOT pull compressor by power cord or air hose.

7. DO NOT adjust or remove safety valve or modify machine.

8. Only operate in well-ventilated area free of combustible materials. DO

NOT smoke while spraying, and do not spray flammable material in

confined area near flame/compressor. Locate compressor at least 20

feet from spray area.

9. Only operate with all guards, covers, and parts in place.

10. Never leave machine running unattended.

11. DO NOT use if cord, plug, or any other electrical equipment becomes

damaged—promptly repair!

12. DO NOT stand on compressor or obstruct airflow to ventilation openings.

13. DO NOT exceed pressure rating of tools or attachments.

14. DO NOT aim compressed air at body or people.

15. Inspect compressor, air lines, valves, and tank for damage, leaks,

weakness, looseness, or excessive wear. Repair/replace defective items

before operating.

16. Drain moisture from tank after each use and promptly replace a damaged

tank. DO NOT attempt to weld on, modify, or repair tank.

17. DO NOT expose to rain or use in wet locations.

18. DO NOT operate under influence of drugs or alcohol or when tired.

19. Prevent unauthorized use by children or untrained users.

S/N

Date

101

102

103

104

105

106

Labels & Cosmetics

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes

off or becomes unreadable, the owner of this machine MUST replace it in the original location

before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

101

PT32335101

GRIZZLY PRO LABEL

104

PT32335104

ELECTRICITY LABEL

102

PT32335102

DRAIN TANK LABEL

105

PT32335105

TOUCH-UP PAINT, GRIZZLY GREEN

103

PT32335103

QR CODE LABEL

106

PT32335106

SPEC/WARNING LABEL

Summary of Contents for QUIET Series









































Search results

Summary of Contents for QUIET Series

Reviews:

Related manuals for QUIET Series

Brands by name

Popular brands

Grizzly QUIET Series, Owner'S Manual

Search results

Summary of Contents for QUIET Series

Reviews:

Related manuals for QUIET Series

Brands by name

Popular brands