background image

-2-

G1028/G1029 Dust Collector

WARNING: For Your Own Safety Read

Instruction Manual Before Operating Collector

Safety Instructions For Power Tools

These safety rules cannot cover every situation in a work shop. Consider your conditions when setting up
or operating your dust collector.

SECTION 1: SAFETY

a)

Always wear eye protection.

b)

Always keep guards in place and in proper
operating condition. 

c)

Keep hands away from inlet during opera-
tion.

9. 

USE PROPER EXTENSION CORD

. Make

sure your extension cord is in good condi-
tion. When using an extension cord, be sure
it is rated Hard Service (grade S) or better.
Conductor size must be 16 A.W.G. for cords
up to 100 feet in length. An undersized cord
will cause a drop in line voltage resulting in
loss of power and overheating. Your exten-
sion cord must also contain a ground wire
and plug pin. Always repair or replace
extension cords if they become damaged.
Minimum Gage for extension cord:

16 A.W.G.

50ft

16 A.W.G.

100ft

14 A.W.G.

200ft

12 A.W.G.

300ft

10. WEAR PROPER APPAREL

Do not wear

loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get
caught in moving parts. Non-slip footwear is
recommended. Wear protective hair covering
to contain long hair.

11. ALWAYS USE SAFETY GLASSES.

Also

use face or dust mask if cutting operation is
dusty. Everyday eyeglasses only have
impact resistant lenses, they are NOT safety
glasses.

1. 

KEEP GUARDS IN PLACE

and in working

order.

2. 

REMOVE ADJUSTING KEYS AND
WRENCHES

. Form habit of checking to see

that keys and adjusting wrenches are
removed from tool before turning on.

3.  KEEP WORK AREA CLEAN

. Cluttered

areas and benches invite accidents.

4. 

DON’T USE IN DANGEROUS ENVIRON-
MENT

. Don’t use power tools in damp or

wet locations, or expose them to rain. Keep
work area well lighted.

5.

KEEP CHILDREN AND VISITORS AWAY

.

All children and visitors should be kept a
safe distance from work area.

6. 

MAKE WORK SHOP CHILD PROOF

with

padlocks, master switches, or by removing
starter keys.

7. 

DON’T FORCE TOOL

. It will do the job bet-

ter and safer at the rate for which it was
designed.

8.  USE RIGHT TOOL.

Don’t force tool or

attachment to do a job for which it was not
designed.

Summary of Contents for G1028

























Reviews: