background image

This shunt resistor must be wired in series with the negative lead of the 
battery pack. The power to run the Cycle Analyst then comes from the 
connection to the positive lead of the battery. 

The  Stand  Alone  Cycle  Analyst  (CA-SA)  includes  a  molded  shunt 
capable of 45 amps of continuous current (100 amps peak) while the 
Direct Plug-in models (CA-DP or -DPS) requires access to the shunt 
resistor inside your motor controller. The High Current model (CA-HC) 
is supplied with terminals to connect to a larger user-supplied shunt. 

The Cycle Analyst picks up the vehicle speed information using either 
a spoke magnet, or in the case of the CA-DP device, through the hall 
sensor signals from a brushless motor controller. 
 

3.

Installation

The  Cycle Analyst  display  box  comes  with  a  mounting  bracket  for 
installation on the handlebar of your bicycle. This bracket can rotate in 
two axis to adjust the display position. Use rubber shims as required 
around the tube if the clamp diameter is too large for your bar. 

In the case of the CA-SA, CA-DPS, and CA-HC models, there is also a 
speedometer pickup cable and spoke magnet. The pickup attaches to 
the fork with two cable ties, and must be mounted to pass within 2mm 
of  the  magnet  for  the  speed  readings  to  register.  For  systems  like 
scooters  or  motorcycles  that  don’t  have  spoked  rims,  a  standard 
magnet can be attached with epoxy to a suitable location on the wheel.

Rotate to Adjust
Handlebar
Clearance

Spoke Magnet

Cable Ties

Ring Terminals
for CA-HC

 

Connector 
for CA-DP(S)

Molded Shunt 
for CA-SA

60” Wire Typical

Speedometer Pickup
(Not in CA-DP)

5

Display Box

Summary of Contents for Cycle Analyst 2.25 CA-DP
























Reviews: