background image

E40.0.01.6C-04 

Operating Manual EASY

LOG

 80CL 

Page 11 of 14 

Recording period 

depending on the chosen measuring cycle 
i. e. 521 days at 3 min measuring cycle 
7.1 years at 15 min measuring cycle 

Alarm function 

alarm points selectable within the measuring range 
and alarm delay adjustable from 0 to 500 min 

Nominal temperature  

25 °C 

Operating temperature 

-

25.0 … +60.0 °C 

Storage temperature 

-

30.0 … +70.0 °C 

Housing 

 

  Dimensions 

48.5 × 48.5 × 35.5 mm  (L × W × D) 
without sensor and plug 

  Design 

ABS housing,  
transparent screen made of polycarbonate,  
splash-proof acc. to IP65 (excl. protection cap) 

  Sensor tube 

about Ø 15 mm, made of polyamide 

  Protection cap 

removable twist plastic head made of 
polycarbonate (IP40) 

 

11.  Disposal 

 

This device must not be disposed as 

“residual waste”. To dispose this device, 

please send it directly to us (adequately stamped). We will dispose it appropri-
ately and environmentally friendly. 

 

 

 

 

DIF

hPa

°C

%

°C

MAX

MIN

SET

1

2

3

© Copyright 2009 GREISINGER electronic GmbH. All Rights Reserved.

  

No part of this documentation may without previous written permission of the 
company GREISINGER electronic GmbH stored in some form, reproduced, 
processed, duplicated or spread become. 
 

Summary of Contents for 602773















Reviews: