1
DESCRIPTION
1.1
PURPOSE
This chainsaw is designed for cutting branches, trunks, logs
and beams of a diameter determined by the cutting length of
the guide bar. It is only designed to cut wood.
It is only to be used in an outdoor, domestic application by
adults.
Do not use the chainsaw for any purpose not listed above.
This chainsaw is not to be used for professional tree services.
It is not to be used by children or by persons not wearing
adequate personal protective equipment and clothing.
1.2
OVERVIEW
Figure 1-22
1
Guide bar cover
2
Front handle guard /
chain brake
3
Front handle
4
Lock out button
5
Trigger
6
Oil tank cap
7
Oil indicator
8
Spike bumpers
9
Saw chain
10
Guide bar
11
Rear handle
12
Chain cover
13
Chain cover knob /
Chain tension knob
14
Battery release button
15
Battery pack
16
Bolt for saw chain
tension
17
Sprocket
18
Bar guide
19
Oil outlet
20
Bar groove
21
Chain drive links
22
Cutter
23
Felling direction
24
Danger zone
25
Escape route
26
Direction of fall
27
Notch
28
Felling back cut
29
Hinge
30
Limb cut
31
Keep work off
ground leave support
limbs until log is cut
32
Log supported along
the entire length
33
Cut from top (over
buck) avoid cutting
earth
34
Log supported one
end
35
Under buck
36
Over buck
37
Log supported both
ends
38
Bucking a log
39
Stand on uphill side
when cutting because
log may roll
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
3
INSTALLATION
WARNING
Do not change or make accessories that are not
recommended by the manufacturer.
WARNING
Do not put in the battery pack until you assemble all the
parts.
3.1
UNPACK THE MACHINE
WARNING
Make sure that you correctly assemble the machine before
use.
WARNING
•
If parts of the machine are damaged, do not use the
machine.
•
If you do not have all the parts, do not operate the
machine.
•
If parts are damaged or missing, contact the service
center.
1. Open the package.
2. Read the documentation provided in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and packing material in compliance with
local regulations.
3.2
ADD THE BAR AND CHAIN
LUBRICANT
Examine the amount of oil in the machine. If the oil level is
low, add the bar and chain lubricant as follows.
IMPORTANT
Use bar and chain lubricant that is only for chains and chain
oilers.
NOTE
The machine comes from the factory without bar and chain
lubricant.
1. Loosen and remove the cap from the oil tank.
2. Put the oil into the oil tank.
3. Monitor the oil indicator to make sure that no dirt enters
in the oil tank while you add the oil.
5
English
EN
Summary of Contents for 2006807
