background image

GREENLEE

FAIRMONT

HG3558B/42307 Portable Power Unit

Greenlee Textron / Subsidiary of Textron Inc.

3

4455 Boeing Dr., Rockford, IL 61109-2988 815/397-7070

THIS SYMBOL MEANS:

ATTENTION!  BECOME ALERT!  YOUR SAFETY IS INVOLVED.

Stop engine before filling fuel tank.
Do not fill fuel tank when engine is
hot. Do not fill fuel tank near an open
flame, sparks, or when smoking. Fuel
is flammable and explosive, and if
ignited will result  in severe injury
or death.

Do not run power unit engine in a confined area.
Engine exhaust fumes are  toxic.  If inhaled,
exhaust fumes can cause injury or death.

Skin Injection Hazard:

High pressure oil easily punctures skin
causing serious injury, gangrene or
death.  If injured seek medical help
immediately to remove oil.

Do not use fingers or hands to check
for leaks.

Depressurize hydraulic system before
servicing.

Do not disconnect tool, hoses or fittings while the
power unit is running or if the hydraulic fluid is hot.
Exposure to hot hydraulic fluid can cause serious
burns.

Failure to observe these warnings could result in
severe bodily injury.

Electrical Shock Hazard:

When using this unit near energized
electrical lines, use only certified
non-conductive hoses and proper
personal protective equipment.

Failure to observe this warning could
result in severe injury or death.

Wear eye protection when operating
this tool.

Failure to wear eye protection can
result in serious eye injury from flying
debris or hydraulic oil.

Safety is a critical factor in the design of Greenlee Fairmont equipment. The best program starts with a
safety-conscious operator. The information highlighted in this bulletin describes operating practices for the
benefit of the workers who will use our equipment in their daily jobs. Comments from users are appreciated.

• Do not operate power unit without

safety guards in place.

• Keep all parts of the body and

loose clothing away from the
engine fan.

SAVE THESE INSTRUCTIONS

Summary of Contents for Fairmont 42307























Reviews: