background image

Greenlee Textron / Subsidiary of Textron

2

4455 Boeing Dr., Rockford, IL 61109-2988    815/397-7070

 940 Series Hydraulic Power Pump

Safety is a critical factor in the design of Greenlee equipment. The best program starts with a safety-conscious
operator. The information highlighted in this bulletin describes operating practices for the benefit of the workers
who will use our equipment in their daily jobs. Comments from users are appreciated.

Hazards or unsafe practices which, if not avoided, COULD
result in minor personal injury or property damage.

Hazards or unsafe practices which, if not avoided, COULD
result in severe personal injury or death.

Immediate hazards which, if not avoided, WILL result in
severe personal injury or death.

SAFETY
ALERT
SYMBOL

The symbol above is used to call your attention
to instructions concerning your personal safety.
Watch for this symbol. It points out important safety
precautions. It means “ATTENTION! Become alert!
Your personal safety is involved!”
 Read the
message that follows and be alert to the possibility
of personal injury or death.

A person who has not read and does not understand all
operating instructions is not qualified to operate this tool.

Failure to read and understand safety instructions may
result in injury or death.

Summary of Contents for 940















Reviews: