12
SEAMLESS BASEPAN
Seamless drawn basepan walls add protection against
water accumulation resulting from storm--driven rain
with heavy wind.
Gree’s deep basepan holds up to 1-3/4 gallons (6.6
liters) of water without spilling. Closed cell foam
insulators are located between the basepan and coils,
keeping coils from direct contact with the basepan
andprovidingadditionalprotectionagainstcorrosion.
CONDENSATE DRAIN VALVE
The temperature--activated drain valve opens when
the outdoor temperature drops below 55
˚
F (12.8
˚
C)
to prevent water from freezing in the basepan.
A07550
Condensate Drain Valve Prevents Water
from Freezing in Basepan
CONDENSATE REMOVAL
SLINGER
RING
CONDENSER SECTION
CONDENSATION
SUCTION PORT
A07678
Condensate Removal System
GA
Gree’s GA series has a new condensate (water)
disposal system. The suction port, along with the
slinger ring, draws in water which is sprayed up onto
the outdoor coil. The water then evaporates, thus
providing better disposal of excess condensate and
improving unit efficiency.
NOTE: If it is necessary to control 100% of the
condensate, the Drain Kit (Part No.: DRAIN-KIT-4PK)
is recommended.
APPLICATIONS
•
Hotels and motels
•
Nursing homes and assisted living care
centers
•
Offices
•
Apartments
•
Single--family dwellings
•
Home conversions and residential add--ons
NEW CONSTRUCTION
ADVANTAGES FOR NEW
CONSTRUCTION
Design Flexibility for the Architect/Engineer
•
Whisper--quiet performance, indoors and out
•
No bulky duct system
•
No separate equipment room
•
No water towers or additional cooling
equipment
•
No complex match--up of different HVAC
components
•
Less sensitivity to building orientation (sun,
wind, shade)
•
Optional architectural grille to permit custom
exterior appearance
Initial Cost Savings for the Building Owner
•
No expensive component HVAC system
purchase
•
No
equipment
room
or
maintenance
engineering staff
•
Two--part delivery to minimize on--site
damage
•
Weather--protected wall sleeve that goes in
place during construction; chassis that slides
in place after construction
•
No seasonal changeover required for cooling
or heating -- units are self--contained comfort
systems
Lower Operating Costs and Reliable Comfort
for The Occupant
•
Heat pump models offer substantial savings
over models with conventional electric
resistance heaters
•
Individual units allow tenants to choose the
degree of comfort and operating economy.
•
Rapid servicing reduces downtime: complete
chassis can be replaced in minutes without
disrupting other occupants.
•
Each unit operates independently of other
units in the building. No dependency by
building on central HVAC system.
RETROFIT/REPLACEMENT
If you are replacing a unit in an existing wall sleeve,
your options include:
•
Replace the existing wall sleeve with the
the polymer wall sleeve. See accessory sleeve
section for selecting the correct sleeve for
your application.
NOTE: in most cases, when replacing the
wall sleeve, the exterior grille must also be
replaced.
•
Use an existing sleeve and exterior grille. The
Gree GA series PTAC will fit into:
—
— Friedrich T series and ZoneAire wall
sleeves, with a required wall sleeve
extension (see accessory Friedrich
Retrofit Wall Sleeve Adapter).
GA
Whether you are designing a new structure or
replacing packaged terminal air conditioning units in
an existing building, Gree GA Series will meet your
needs.
The Gree GA series Packaged Terminal Air
Conditioning (PTAC) unit is designed to meet the
needs of the architect, engineer, and contractor. For
unit installation, Gree’s expert support network will
assist in all applicable aspects of the construction
project, from preparing a budget to start-up.
4
The following major competitors’ wall
sleeves/grilles: Carrier, GE, Amana,
Trane, Friedrich and Bryant, and NO
accessory retrofit kit is required.