18
FIELD--INSTALLED ACCESSORIES (CONT.)
OUTDOOR GRILLES
Aluminum Architectural
Outdoor Grilles (Louvered)
Part No.: GRILLE--ALU--CLEAR
(anodized aluminum)
Part No.: GRILLE--ALU--WHITE
Part No.: GRILLE--ALU--BEIGE
Part No.: GRILLE--ALU--ALPIN
(color matches
wall sleeve)
Part No.: GRILLE--ALU--BRONZ
Part No.: GRILLE--ALU--MBRNZ
Part No.: GRILLE--ALU--BROWN
Polymeric Architectural Outdoor Grilles
(Louvered)
Part No.: GRILLE--PLA--BEIGE
Part No.: GRILLE--PLA--ALPIN
(color matches Gree’s polymer wall sleeve)
This value line of polymeric architectural outdoor
grilles will blend attractively with most building
exteriors. Mounted easily from inside the room, the
one--piece, molded grille is designed for protection,
enhanced appearance, and superior weather-resistance.
The grille is made of durable polymer and has a
colorfast, lightly textured finish that blends well with
most exterior finishes.
Architectural Grille in
Aluminum or Polymeric
Standard Outdoor Aluminum Grille
Part No.: GRILLE--ALU--STAMP
This cost--effective, one--piece standard grille is made
from durable anodized aluminum. The grille is
lightweight, has a clear finish, and is easy to install
from inside the room.
Standard Grille
GA
Gree recommends only the use of Gree-supplied
grilles for use with the GA series units. However, the
architectural designs of a building may dictate the use
of special or oversized grilles and/or louvers. Special
louvers or any special architectural treatment of the
building facade that may restrict free circulation
of condenser airflow should be referred to Gree
Corporation for evaluation and approval.
This premium line of decorative outdoor grilles will
enhance the appearance of any building. The grilles
are made of strong, durable, extruded, anodized
aluminum and are designed to be mounted easily from
inside the room. These elegant grilles, available in
many standard colors, have baked enamel finishes
containing 50% Kynar
®
resin, for a superior finish that
will withstand the most extreme conditions.
APPLICATIONS
•
Hotels and motels
•
Nursing homes and assisted living care
centers
•
Offices
•
Apartments
•
Single--family dwellings
•
Home conversions and residential add--ons
NEW CONSTRUCTION
ADVANTAGES FOR NEW
CONSTRUCTION
Design Flexibility for the Architect/Engineer
•
Whisper--quiet performance, indoors and out
•
No bulky duct system
•
No separate equipment room
•
No water towers or additional cooling
equipment
•
No complex match--up of different HVAC
components
•
Less sensitivity to building orientation (sun,
wind, shade)
•
Optional architectural grille to permit custom
exterior appearance
Initial Cost Savings for the Building Owner
•
No expensive component HVAC system
purchase
•
No
equipment
room
or
maintenance
engineering staff
•
Two--part delivery to minimize on--site
damage
•
Weather--protected wall sleeve that goes in
place during construction; chassis that slides
in place after construction
•
No seasonal changeover required for cooling
or heating -- units are self--contained comfort
systems
Lower Operating Costs and Reliable Comfort
for The Occupant
•
Heat pump models offer substantial savings
over models with conventional electric
resistance heaters
•
Individual units allow tenants to choose the
degree of comfort and operating economy.
•
Rapid servicing reduces downtime: complete
chassis can be replaced in minutes without
disrupting other occupants.
•
Each unit operates independently of other
units in the building. No dependency by
building on central HVAC system.
RETROFIT/REPLACEMENT
If you are replacing a unit in an existing wall sleeve,
your options include:
•
Replace the existing wall sleeve with the
the polymer wall sleeve. See accessory sleeve
section for selecting the correct sleeve for
your application.
NOTE: in most cases, when replacing the
wall sleeve, the exterior grille must also be
replaced.
•
Use an existing sleeve and exterior grille. The
Gree GA series PTAC will fit into:
—
— Friedrich T series and ZoneAire wall
sleeves, with a required wall sleeve
extension (see accessory Friedrich
Retrofit Wall Sleeve Adapter).
GA
Whether you are designing a new structure or
replacing packaged terminal air conditioning units in
an existing building, Gree GA Series will meet your
needs.
The Gree GA series Packaged Terminal Air
Conditioning (PTAC) unit is designed to meet the
needs of the architect, engineer, and contractor. For
unit installation, Gree’s expert support network will
assist in all applicable aspects of the construction
project, from preparing a budget to start-up.
4
The following major competitors’ wall
sleeves/grilles: Carrier, GE, Amana,
Trane, Friedrich and Bryant, and NO
accessory retrofit kit is required.
