Gree GMV-Q1010WM/B-X Owner'S Manual Download Page 43 | Manualshive

Page: 43 / 68

Gree GMV-Q1010WM/B-X Owner'S Manual Download Page 43

Heat Recovery DC Inverter Multi VRF Unit

40

Fig 41 Connection of communication for multi-module system and multi-module converter system

Note:

①

For modular outdoor units, if there are multiple outdoor modules, the master unit must be the

first outdoor module on the communication wire and cannot be connected to i ndoor units. (The

master unit is set by SA8 on the main board of outdoor unit.)

②

For modular outdoor units, if there are multiple outdoor modules, indoor units must be

connected to the last outdoor slave module.

③

Communication wire and power cord must be laid separately to avoid interference.

④

Communication wire shall be long enough

. It’s not recommended to connect wire by peeling

away its outer layer.

⑤

Heat pump mode exchanger must be connected in series and the last mode exchanger must

be connected with a matching resistance (provided among the accessory parts of outdoor unit).

Connect the matching resistance to the D1, D2 terminals of wiring board XT2 of mode exchanger.

⑥

Adopt the one-to-one connection method for the connection between heat pump mode

converter and downstream iindoor unit. Each brach is corresponding to one communication terminal.

“1D1,1D2” indicates the terminal position of comunication wire for the downstream indoor unit of the
first branch; “2D1, 2D2” indicates the terminal position of comunication wire for the downstream

indoor unit of the second branch and by this analogy.

Please note that there’s corresponding mark at

«
...
41
42
43
44
45
...
»

Summary of Contents for GMV-Q1010WM/B-X





































































Reviews:

No comments