Gree GMV-NDX42P/A-T Owner'S Manual Download Page 5 | Manualshive

Page: 5 / 28

Gree GMV-NDX42P/A-T Owner'S Manual Download Page 5

Multi Variable Air Conditioners Fresh Air Series Indoor Unit

2

(25) Volatile liquid, such as diluent or gas will damage the unit appearance. Only use soft cloth with a little neutral

detergent to clean the outer casing of unit.

(26) If anything abnormal happens (such as burning smell), please power off the unit and cut off the main power

supply, and then immediately contact Gree appointed service center. If abnormality keeps going, the unit

might be damaged and lead to electric shock or fire.

GREE will not assume responsibility of personal injury or equipment damage caused

by improper installation and commission, unnecessary service and incapable of following

the rules and instructions listed in this manual.

2 Product Introduction

2.1 Unit Introduction

VRF fresh air series indoor unit is a kind of air processing unit that inhales the fresh air

from outdoor side and then processes it to provide for the user in the room. According to

the different selected air volume, there are two kinds of connection method for the VRF

fresh air series indoor unit:

(1) If the selected air volume

≤1471 CFM, connect with normal indoor units by blow

method, or connect with the fixed outdoor unit as shown in

（

2

）

.

Model of Indoor Unit

Model of Outdoor Unit

GMV-NDX42P/A-T(U)

Connecting condition with GMV-**WM/B-F(U) series modular outdoor unit:
The  total  capacity  of  connected  fresh  air  series  indoor  units  and  conventional
VRF  indoor  units  must  be  within  50%~100%  of  the  capacity  of  outdoor  unit,
among  which,  the  total  capacity  of  connected  fresh  air  indoor  units  cannot
exceed 30% of the capacity of outdoor unit.

GMV-NDX48P/A-T(U)

GMV-NDX54P/A-T(U)

GMV-NDX72P/A-T(U)

GMV-NDX96P/A-T(U)

NOTICE!

When fresh air series indoor units and conventional VRF indoor units will be

connected, please follow the capacity requirement strictly. The total capacity of connected

fresh air indoor units cannot exceed 30% of the capacity of outdoor unit, while the total

capacity of indoor units shall be within 50%~100% of the capacity of outdoor unit.

Otherwise, the comfortableness will be affected or even the unit will be damaged.

«
...
3
4
5
6
7
...
»

Summary of Contents for GMV-NDX42P/A-T





























Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands