background image

Multi Variable Air Conditioners Fresh Air Series Indoor Unit 

18 

5.1 Connection of Wire and Patch Board Terminal 

(1)   The connection of wire (as shown in fig 5.1.1) 

1) Strip about 25mm (1in.) insulation of the wire end by stripping and cutting tool. 

2) Remove the wiring screws on the terminal board. 

3) Shape the tail of wire into ring by needle nose plier, and keep the gauge of ring in 

accordance with screw. 

4) Use the screwdriver for tightening the terminal. 

(2)   The connection of stranded wire (as shown in fig 5.1.2) 

1) Strip  about 10mm (3/8in.)  insulation  of the end  of stranded  wire by stripping  and 

cutting tool. 

2) Loosen the wiring screws on terminal board. 

3) Insert the wire into the ring tongue terminal and tighten by crimping tool. 

4) Use the screwdriver for tightening the terminal. 

 

 

Fig 5.1.1                                                          Fig 5.1.2 

5.2 Power Cord Connection 

 

1

Every unit should be equipped with a circuit breaker for short-circuit and overload protection.

 

2

During  operation,  all  indoor  units  connected  to  the  same  outdoor  unit  system  must  be  kept  energized 

status. 

Otherwise, the unit can’t operate normally. 

 

 

Fig 5.2.1 

 

Summary of Contents for GMV-NDX42P/A-T





























Reviews: