background image

Multi Variable Air Conditioners Floor and Ceiling Type Indoor Unit

 

3.2 Installation Position Selection 

(1)  The location should be able to withstand the weight of unit. 
(2)  The water can be drained conveniently from drainage pipe. 
(3)  There should be no obstruction near air inlet and air outlet. 
(4)  Follow the installation distance required in the Fig.3.2 below to ensure sufficient space 

for maintenance. 

(5)  The installation location should be far from heat sources, flammable or explosive gas, 

or smog spread in the air. 

(6)  The indoor unit, outdoor unit, power cord and connection electricity wire should be at 

least 1m from television and radio in order to prevent interference and noise. (Even 
though 1m distance is ensured, there may be noise if the electric wave is too strong.) 

Unit: mm 

Floor type 

 

 

Ceiling type 

 

Fig.3.2 

Notes:

 

 The unit shall be installed in accordance with national standards or local regulations. 

 Only qualified personnel can carry out installation work, please contact with local dealer 

before installation. 

 Make sure all the installation work completed before energizing. 

Summary of Contents for GMV-ND112ZD/B-T




























Reviews: