background image

DC Inverter Multi VRF System 

27 

Outdoor: 

Error Code 

Content 

Error Code 

Content 

E0 

Malfunction of ODU (uniform) 

F0 

Main board of ODU is poor 

E1 

High-pressure protection 

F1 

Malfunction of high-pressure sensor 

E2 

Discharge low-temperature protection 

F3 

Malfunction of low-pressure sensor 

E3 

Low-pressure protection 

F5 

Malfunction of discharge temperature 
sensor of compressor 1 

E4 

High discharge temperature protection 
of compressor 

FP 

Malfunction of DC motor 

E5 

High discharge temperature protection 
of compressor 1 

b1 

Malfunction of outdoor ambient 
temperature sensor 

EC 

Drop protection of discharge 
temperature sensor of compressor 1 

b2 

Malfunction of defrosting temperature 
sensor 1 

J1 

Over-current protection of compressor 

b4 

Malfunction of liquid temperature 
sensor of sub-cooler 

J7 

Gas-mixing protection of 4-way valve 

b5 

Malfunction of gas temperature sensor 
of sub-cooler 

J8 

High pressure ratio protection of 
system 

b6 

Malfunction of inlet tube temperature 
sensor of vapor liquid separator 

J9 

Low pressure ratio protection of system 

b7 

Malfunction of exit tube temperature 
sensor of vapor liquid separator 

JA 

Protection because of abnormal 
pressure 

b9 

Malfunction of gas temperature sensor 
of heat exchanger 

JC 

Water flow switch protection 
(GMV-12WP/A-T(U) is Water Full 
Protection) 

bA 

Malfunction of oil-return temperature 
sensor 1 

JL 

Protection because high pressure is 
too low 

bH 

Clock of system is abnormal 

P0 

malfunction of driving board of 
compressor (uniform) 

H0 

Malfunction of driving board of fan 
(uniform) 

P1 

Driving board of compressor operates 
abnormally (uniform) 

H1 

Driving board of fan operates 
abnormally (uniform) 

P2 

Voltage protection of driving board 
power of compressor (uniform) 

H2 

Voltage protection of driving board 
power of fan (uniform) 

P3 

Reset protection of driving module of 
compressor 

H3 

Reset protection of driving module of 
fan 

P4 

Drive PFC protection of compressor 

H4 

Drive PFC protection of fan 

P5 

Over-current protection of inverter 
compressor 

H5 

Over-current protection of inverter fan 

P6 

Drive IPM module protection of 
compressor 

H6 

Drive IPM module protection of fan 

P7 

Malfunction of drive temperature 
sensor of compressor 

H7 

Malfunction of drive temperature 
sensor of fan 

P8 

Drive IPM high temperature protection 
of compressor 

H8 

Drive IPM high temperature protection 
of fan 

P9 

Desynchronizing protection of inverter 
compressor 

H9 

Desynchronizing protection of inverter 
fan 

PH 

High-voltage protection of 
compressor’s drive DC bus bar 

HH 

High-voltage protection of fan’s drive 
DC bus bar 

PC 

Malfunction of current detection circuit 
drive of compressor 

HC 

Malfunction of current detection circuit 
of fan drive 

PL 

Low voltage protection for DC bus bar 
of drive of compressor 

HL 

Low voltage protection of bus bar of 
fan drive 

PE 

Phase-lacking of inverter compressor 

HE 

Phase-lacking of inverter fan 

PF 

Malfunction of charging loop of driven 
of compressor 

HF 

Malfunction of charging loop of fan 
drive 

Summary of Contents for GMV-12WP/A-T




































Reviews: