Gree GKH18K3HI Owner'S Manual Download Page 35

Page: 35 / 40

Cassette Type Air Conditioner Unit

Power lines should go along the right side plate and be fixed to the fixation hook

with binding wires to keep no contact with pipelines. Communication lines between

indoor and outdoor units also should go along the right side plate and keep away from

power lines.

5 Installation of Controllers

Refer to the Installation Manual of the controller for more details.

6 Test Running

6.1 Trial Operation and Testing

(1).

The meaning of error codes as shown below:

Table 6.1

Number

Error code

Error

Remarks

Compressor high pressure protection

Indoor anti-freeze protection

Compressor low pressure protection, refrigerant lack

protection and refrigerant colleting mode

Compressor high discharge temperature protection

Communication error

Full water protection

Indoor ambient temperature sensor error

Evaporator temperature sensor error

Condenser temperature sensor error

Outdoor ambient temperature sensor error

Discharge temperature sensor error

Temperature sensor error of wired controller

Compressor overload protection

Overloading

4-way valve direction changing protection

Outdoor unit capacity code error

Indoor unit capacity code error

Note:

When the unit is connected with the wired controller, the error code will be simultaneously shown

Summary of Contents for GKH18K3HI









































Search results

Summary of Contents for GKH18K3HI

Reviews:

Related manuals for GKH18K3HI

Brands by name

Popular brands

Gree GKH18K3HI, Owner'S Manual

Search results

Summary of Contents for GKH18K3HI

Reviews:

Related manuals for GKH18K3HI

Brands by name

Popular brands