3. Use an R/C radio system that is in first-class condition,
and a correctly sized engine throughout the building
process.
4. You must properly install the R/C radio system and other
components so that the model operates correctly on the
ground and in the air.
5. You must test the operation of the model before
every
flight to insure that all equipment is operating and you must
make certain that the model has remained structurally
sound. Be sure to check clevises or other connectors often
and replace them if they show signs of wear or fatigue.
Remember: Take your time and follow directions to end
up with a well-built model that is straight and true.
Please inspect all parts carefully before starting to build!
YOU CAN CONTACT US...
If any parts are missing, broken or defective, or if you
have any questions about building or flying this
airplane, please call us at (217) 398-8970. You can also
check our web site at
www.greatplanes.com
for the
latest SpaceWalker ARF updates, or e-mail your
questions to
If you
are calling for replacement parts, please reference the
part numbers and have them ready when calling.
Items in parentheses (GPMQ4243) are suggested part
numbers recognized by distributors and hobby shops and
are listed for your ordering convenience.
GPM
is the Great
Planes brand,
TOP
is the Top Flite
®
brand, and
HCA
is the
Hobbico
®
brand.
❏
4-Channel Radio With 4 Standard Servos and 1 servo
with 45 oz.-in. or more of torque
❏
Engine –
See
Engine Selection
❏
Propeller (Top Flite
®
Power Point
™
–Refer To Your
Engine’s Instructions For Proper Size)
❏
Medium Fuel Tubing (GPMQ4131)
❏
1/4 Scale Pilot Figure
❏
1/4" Foam Rubber (HCAQ1000)
❏
Switch and Charge Jack (GPMM1000)
❏
Large Scale Control Horns (2)
❏
24" Servo Extension (2)
❏
“Y” Harness
These are the building tools that are required.
We
recommend
Great Planes Pro
™
CA and Epoxy glue.
❏
1/2 oz. Pro CA (Thin, GPMR6001)
❏
1 oz. Pro CA+ (Medium, GPMR6008)
❏
6-Minute Pro Epoxy (GPMR6045)
❏
30-Minute Pro Epoxy (GPMR6047)
❏
Epoxy Brushes (GPMR8060)
❏
Mixing Cups (GPMR8056)
❏
Canopy Glue
❏
Pro Thread Locking Compound (GPMR6060)
❏
T-pins (HCAR5150)
❏
Isopropyl Alcohol (70%)
❏
Hobby Knife (HCAR0105), #11 Blades (HCAR0211)
❏
Dead Center
™
Hole Locator (GPMR8130)
❏
Small Phillips and Flat Blade Screwdrivers
❏
Pliers w/Wire Cutter (HCAR0630)
❏
4mm Hex Wrench (HCAR0521)
❏
Sealing Iron (COVR2700)
❏
Heat Gun (TOPR2000)
❏
Straightedge w/Scale (HCAR0475)
❏
Builders Triangle Set (HCAR0480)
❏
Masking Tape (TOPR8018)
❏
Sandpaper (coarse, medium, fine grit)
❏
Easy-Touch
™
Bar Sander (GPMR6170, or similar)
❏
Paper Towels
❏
Electric Drill
❏
Drill Bits: 1/16", 7/64", 1/8", 3/32", 3/16", 7/32" 5/32"
1/4", 5/64" (HCAR0699)
❏
Petroleum Jelly
❏
CA Applicator Tips (HCAR3780)
❏
CA Debonder (GPMR6039)
❏
Curved Tip Canopy Scissors For Trimming
Plastic Parts (HCAR0667)
❏
Fuel Filler Valve (GPMQ4160)
❏
Bar Of Hand Soap
Optional Supplies and Tools
Building Supplies and Tools
Required Accessories
PREPARATIONS
Engine Selection
There are several engines that will work well in your
SpaceWalker ARF. We recommend a
hot
2-stroke such
as an
O.S.
®
.61FX
or
SuperTigre
™
G61
. For unsurpassed
power and realistic sound, an
O.S. FS-70 or FS-90
4-stroke can’t be beat.
DECISIONS YOU MUST MAKE
Note
: We, as the kit manufacturer, provide you with a
top quality kit and great instructions, but ultimately the
quality of your finished model depends on how
you
build
it; therefore, we cannot in any way guarantee
the performance of your completed model, and no
representations are expressed or implied as to the
performance or safety of your completed model.
3
