background image

Ground check the operational range of your radio before the
first flight of the day. With the transmitter antenna collapsed
and the receiver and transmitter on, you should be able to
walk at least 100 feet away from the model and still have
control. Have an assistant stand by your model and, while
you work the controls, tell you what the control surfaces are
doing. Repeat this test with the motor running at various
speeds with an assistant holding the model, using hand
signals to show you what is happening. If the control
surfaces do not respond correctly, do not fly! Find and
correct the problem first. Look for loose servo connections
or broken wires, corroded wires on old servo connectors,
poor solder joints in your battery pack or a defective cell, or
a damaged receiver crystal from a previous crash.

Get help from an experienced pilot when learning to
operate motors.

Use safety glasses when running motors.

Do not run the motor in an area of loose gravel or sand; the
propeller may throw such material in your face or eyes.

Keep your face and body as well as all spectators away from
the plane of rotation of the propeller as you run the motor.

Keep these items away from the prop: loose clothing, shirt
sleeves, ties, scarfs, long hair or loose objects such as
pencils or screwdrivers that may fall out of shirt or jacket
pockets into the prop.

The motor gets hot! Do not touch it during or right after
operation.

Read and abide by the following Academy of Model
Aeronautics Official Safety Code:

GENERAL
1. I will not fly my model aircraft in sanctioned events, air
shows, or model flying demonstrations until it has been
proven to be airworthy by having been previously
successfully flight tested.

2. I will not fly my model aircraft higher than approximately
400 feet within 3 miles of an airport without notifying the

airport operator. I will give right of way to, and avoid flying in
the proximity of full-scale aircraft. Where necessary an
observer shall be used to supervise flying to avoid having
models fly in the proximity of full-scale aircraft.

3. Where established, I will abide by the safety rules for the
flying site I use, and I will not willfully and deliberately fly my
models in a careless, reckless and/or dangerous manner.

4. I will not fly my model unless it is identified with my name
and address or AMA number, on or in the model.

5. I will not operate models with pyrotechnics (any device
that explodes, burns, or propels a projectile of any kind).

RADIO CONTROL
1. I will have completed a successful radio equipment ground
check before the first flight of a new or repaired model.

2. I will not fly my model aircraft in the presence of
spectators until I become a qualified flier, unless assisted by
an experienced helper.

3. I will perform my initial turn after takeoff away from the pit
or spectator areas, and I will not thereafter fly over pit or
spectator areas, unless beyond my control.

4. I will operate my model using only radio control frequencies
currently allowed by the Federal Communications Commission.

1. Check the C.G. according to the measurements

provided in the manual.

2. Be certain the battery, speed control, and receiver

are securely mounted in the fuse. Simply stuffing
them into place with foam rubber is not sufficient.

3. Extend your receiver antenna and make sure it has

been properly attached to the airplane.

4. Balance your model laterally as explained in the

instructions.

5. Use thread locking compound to secure critical

fasteners such as the set screws that hold the wheel
collars.

6. Add a drop of oil to the axles so the wheels will

turn freely.

During the last few moments of preparation your mind
may be elsewhere anticipating the excitement of the first
flight. Because of this, you may be more likely to overlook
certain checks and procedures that should be performed
before the model is flown. To help avoid this, a check list
is provided to make sure these important areas are not
overlooked. Many are covered in the instruction manual,
so where appropriate, refer to the manual for complete
instructions.

CHECK LIST

AMA SAFETY CODE (excerpt)

Failure to follow these safety precautions may result
in severe injury to yourself and others.

MOTOR SAFETY PRECAUTIONS

Range Check

14

Summary of Contents for Micro Whizz

















Reviews: