background image

26

Ground Check and Range Check

Run the engine for a few minutes to make sure it idles reliably, 
transitions smoothly and maintains full power indefi nitely. 

Afterward, shut the engine off and inspect the model closely, 

making sure all fasteners, pushrods and connections have 
remained tight and the hinges are secure. Always ground 
check the operational range of your radio before the fi rst fl ight 
of the day following the manufacturer’s instructions that came 
with your radio. This should be done once with the engine off 
and once with the engine running at various speeds. If the 
control surfaces do not respond correctly, 

do not fl y!

 Find and 

correct the problem fi rst. Look for loose servo connections 
or broken wires, corroded wires on old servo connectors, 
poor solder joints in your battery pack or a defective cell, or 
a damaged receiver crystal from a previous crash.

ENGINE SAFETY PRECAUTIONS

Failure to follow these safety precautions may result 
in severe injury to yourself and others.

Keep  all  engine  fuel  in  a  safe  place,  away  from  high  heat, 
sparks or fl ames, as fuel is very fl ammable. Do not smoke 
near the engine or fuel; and remember that engine exhaust 
gives off a great deal of deadly carbon monoxide. Therefore

 

do not run the engine in a closed room or garage

.

Get help from an experienced pilot when learning to operate 
engines.

Use safety glasses when starting or running engines.

Do not run the engine in an area of loose gravel or sand; the 
propeller may throw such material in your face or eyes.

Keep your face and body as well as all spectators away from 
the plane of rotation of the propeller as you start and run the 
engine.

Keep these items away from the prop: loose clothing, shirt 
sleeves, ties, scarfs, long hair or loose objects such as pencils 
or  screwdrivers  that  may  fall  out  of  shirt  or  jacket  pockets 
into the prop.

Use a “chicken stick” or electric starter to start the engine. 
Do not use your fi ngers to fl ip the propeller. Make certain the 

glow plug clip or connector is secure so that it will not pop off 
or otherwise get into the running propeller.

Make all engine adjustments from behind the rotating propeller.

The engine gets hot! Do not touch it during or right after 

operation. Make sure fuel lines are in good condition so fuel 
will not leak onto a hot engine, causing a fi re.

To stop a glow engine, cut off the fuel supply by closing 

off the fuel line or following the engine manufacturer’s 
recommendations. Do not use hands, fi ngers or any other 
body part to try to stop the engine. To stop a gasoline powered 
engine an on/off switch should be connected to the engine coil. 
Do not throw anything into the propeller of a running engine.

AMA SAFETY CODE

Read and abide by the following excerpts from the Academy 
of Model Aeronautics Safety Code. For the complete Safety 
Code refer to 

Model Aviation

 magazine, the AMA web site or 

the Code that came with your AMA license.

General

1) I will not fl y my model aircraft in sanctioned events, air shows, 

or model fl ying demonstrations until it has been proven to be 
airworthy by having been previously, successfully fl ight tested.

2) I will not fl y my model aircraft higher than approximately 

400 feet within 3 miles of an airport without notifying the 

airport operator. I will give right-of-way and avoid fl ying in the 
proximity of full-scale aircraft. Where necessary, an observer 
shall be utilized to supervise fl ying to avoid having models fl y 
in the proximity of full-scale aircraft.

3) Where established, I will abide by the safety rules for the 
fl ying site I use, and I will not willfully and deliberately fl y my 
models in a careless, reckless and/or dangerous manner.

5) I will not fl y my model unless it is identifi ed with my name 
and address or AMA number, on or in the model. Note: This 
does not apply to models while being fl own indoors.

7) I will not operate models with pyrotechnics (any device that 

explodes, burns, or propels a projectile of any kind).

Radio Control

1) I will have completed a successful radio equipment ground 

check before the fi rst fl ight of a new or repaired model.

2) I will not fl y my model aircraft in the presence of spectators 
until I become a qualified flier, unless assisted by an 
experienced helper.

3) At all fl ying sites a straight or curved line(s) must be 
established in front of which all fl ying takes place with the 
other side for spectators. Only personnel involved with fl ying 
the aircraft are allowed at or in the front of the fl ight line. 
Intentional fl ying behind the fl ight line is prohibited.

4) I will operate my model using only radio control frequencies 

currently allowed by the Federal Communications Commission.

5) 

I will not knowingly operate my model within three miles 

of any pre-existing fl ying site except in accordance with 
the frequency sharing agreement listed

 [in the complete 

AMA Safety Code].

9) Under no circumstances may a pilot or other person touch 
a powered model in fl ight; 

nor should any part of the model 

other than the landing gear, intentionally touch the ground, 
except while landing.

Summary of Contents for F1 Rocket Evo





























Reviews: