background image

turn the model, simply input the elevator or rudder a little sooner 
or later in the rotation. It’s all a matter of timing.

PINWHEEL

Climb vertically and bring the model to a vertical hover, but do 
not stop long enough to let the torque pull the model around 
(climbing or sliding slightly will not be noticeable to spectators 
but will keep air fl owing over the ailerons and provide you roll 
authority to stop the torque). When the model is hanging, 
rock the plane left with rudder, then apply full throttle and 
full right rudder and hold both, completing 3/4 of a VERY 
tight Knife Edge Loop and fl ying out Knife Edge. When done 
correctly, the plane pivots around the wingtip in a very small 
area. This maneuver can be done either direction.

OTHER ITEMS AVAILABLE

FROM GREAT PLANES

ElectriFly RimFire

 42-50-800 Out-Runner Brushless Motor

Powered by rare-earth Neodymium magnets, RimFire out-
runner motors produce explosive acceleration in planes 
ranging from park fl yers to 1.60-size giants! Their high-
torque design eliminates the need for a gearbox, making 
them the simpler, lighter and less expensive alternative to a 
brushed motor and gearbox. Plus, their innovative housing 
optimizes cooling, allowing RimFire motors to produce 50% 
more performance power than out-runners of similar size. 
Prop adapter, motor mount and hardware are included. The 
installed, gold-plated bullet connectors are compatible with 
all ElectriFly ESCs. GPMG4700

ElectriFly Silver Series 45A Brushless ESC 
With Silver Series brushless ESCs, the only way their 
performance would be any easier to enjoy is if they came 
already installed. As it is, hook-up takes only seconds — and 
set-up takes no time at all. Silver Series brushless ESCs do 
it automatically on hook-up, and offer the option to use brake 
(or not) with a flick of the throttle stick. The Silver Series 
45A is NiCd, NiMH and LiPo-compatible, with a 5V/2A BEC 
capable of handling 3 or 4 standard servos. Includes all 
connectors. GPMM1840

ElectriFly Power Series 2100mAh 20C Balanced
LiPo Battery
LiPo cells offer three times the voltage of NiCd and NiMH 
cells, at less than half the weight. Rated at a true 20C 
continuous discharge (30C burst for 30 seconds), this 
ElectriFly LiPo pack comes wired for balanced — allowing 
each cell to be charged to the maximum 4.2V. The result: 
Maximum power to your motor for maximum performance in 
the air! The battery features quality Deans

®

 Ultra Plugs

®

 and 

balancing connector. Recharge using the ElectriFly Equinox

 

Cell Balancer for maximum power per cell. GPMP0618

Summary of Contents for EDGE 540 T Performance Series

























Reviews: