GREAT PLANES Cherokee .40 ARF Instruction Manual Download Page 26

26

ENGINE SAFETY PRECAUTIONS

Failure to follow these safety precautions may result 
in severe injury to yourself and others.

Keep all engine fuel in a safe place, away from high heat, 
sparks or fl ames, as fuel is very fl ammable. Do not smoke 
near the engine or fuel; and remember that engine exhaust 
gives off a great deal of deadly carbon monoxide. Therefore, 
do not run the engine in a closed room or garage.

Get help from an experienced pilot when learning to operate 
engines. 

Use safety glasses when starting or running engines.

Do not run the engine in an area of loose gravel or sand; the 
propeller may throw such material in your face or eyes.

Keep your face and body as well as all spectators away from 
the plane of rotation of the propeller as you start and run
the engine.

Keep these items away from the prop: loose clothing, shirt 
sleeves, ties, scarves, long hair or loose objects such as 
pencils or screwdrivers that may fall out of shirt or jacket 
pockets into the prop.

Use a “chicken stick” or electric starter to start the engine. 
Do not use your fi ngers to fl ip the propeller. Make certain the 
glow plug clip or connector is secure so that it will not pop off 
or otherwise get into the running propeller. 

Make all engine adjustments from behind the rotating propeller.

The engine gets hot! Do not touch it during or right after 
operation. Make sure fuel lines are in good condition so fuel 
will not leak onto a hot engine, causing a fi re.

To stop a glow engine, cut off the fuel supply by closing 
off the fuel line or following the engine manufacturer's 
recommendations. Do not use hands, fi ngers or any other 
body part to try to stop the engine. Do not throw anything into 
the propeller of a running engine.

LITHIUM BATTERY HANDLING & USAGE

WARNING!! Read the entire instruction sheet included with 
your battery. Failure to follow all instructions could cause 
permanent damage to the battery and its surroundings, and 
cause bodily harm!

•  

ONLY use a LiPo approved charger. NEVER use a NiCd/
NiMH peak charger!

•  NEVER charge in excess of 4.20V per cell.
•  

ONLY charge through the “charge” lead. NEVER charge 
through the “discharge” lead.

•  NEVER charge at currents greater than 1C.
•  ALWAYS set charger’s output volts to match battery volts.
•  ALWAYS charge in a fi reproof location.
• NEVER 

trickle 

charge.

•  

NEVER allow the battery temperature to exceed 150° F 
[65° C].

•  

NEVER disassemble or modify pack wiring in any way or 
puncture cells.

•  NEVER discharge below 2.5V per cell.
•  

NEVER place on combustible materials or leave 
unattended during charge or discharge.

•  ALWAYS KEEP OUT OF REACH OF CHILDREN.

AMA SAFETY CODE (excerpts)

Read and abide by the following excerpts from the Academy 
of Model Aeronautics Safety Code. For the complete Safety 
Code refer to Model Aviation magazine, the AMA web site or 
the Code that came with your AMA license.

General

1) I will not fl y my model aircraft in sanctioned events, air shows, 
or model fl ying demonstrations until it has been proven to be 
airworthy by having been previously, successfully fl ight tested.

2) I will not fl y my model aircraft higher than approximately 
400 feet within 3 miles of an airport without notifying the 
airport operator. I will give right-of-way and avoid fl ying in the 
proximity of full-scale aircraft. Where necessary, an observer 
shall be utilized to supervise fl ying to avoid having models fl y 
in the proximity of full-scale aircraft.

3) Where established, I will abide by the safety rules for the 
fl ying site I use, and I will not willfully and deliberately fl y my 
models in a careless, reckless and/or dangerous manner.

5) I will not fl y my model unless it is identifi ed with my name 
and address or AMA number, on or in the model. Note: This 
does not apply to models while being fl own indoors.

7) I will not operate models with pyrotechnics (any device 
that explodes, burns, or propels a projectile of any kind).

Summary of Contents for Cherokee .40 ARF





























Reviews: