GREAT PLAINS Terra Max HT1110-6.0M Operator'S Manual Download Page 5

Page: 5 / 42

HT1110-6.0M & 7.5M

Table of Contents

Introduction

Great Plains

| 588-206M | 3/21/22

Table of Contents

Introduction

Great Plains’ Terra Max is a pull-type unit designed

for tilling and working soil. Every Terra Max we build

is designed and built with care using only quality

materials. For the best user experience, read this

manual and follow all instructions carefully. These

pages will guide you through the operation and

contain tips for easier adjustment and maintenance.
All information in this manual is current as of

publication. Information contained within is subject

to change to ensure top performance.

Terra Max Models Covered
Document Family

See “

Terra Max® Specifications and Capacities

” on

page 36 for precise swath information.

Owner Assistance

If you need customer service or repair parts, contact a Great

Plains dealer. They have trained personnel, repair parts and

equipment specially designed for Great Plains products.
Your machine’s parts were specially designed and should only

be replaced with Great Plains parts. Always use the serial and

model number when ordering parts from your Great Plains

dealer. The serial-number plate is located on the left side main

frame, below bypass and down pressure valve.

Record your machine’s model and serial number on the inside

cover of this manual for quick reference.

Further Assistance

Great Plains Manufacturing, Inc. and your Great Plains dealer

want you to be satisfied with your new Terra Max. If for any

reason you do not understand any part of this manual or are

otherwise dissatisfied, please take the following actions first:
1. Discuss the matter with your dealership service manager.

Make sure they are aware of any problems so they can

assist you.

2. If you are still unsatisfied, seek out the owner or general

manager of the dealership.

If your dealer is unable to resolve the problem or the issue is

parts related, please contact:

Great Plains Service Department

1525 E. North St.

P.O. Box 5060

Salina, KS 67402-5060

Or go to

www.greatplainsag.com

and follow the contact

information at the bottom of your screen for our service

department.

588-206M

Operator Manual (this document)

588-206Q-ENG Pre-Delivery Manual
588-206P

Parts Manual

Great

Plain

MAN

UFAC

TURIN

G IN

COR

POR

ATED

SALIN

A, KS

6740

*GP

-000*

Coun

try o

f Orig

in - U

Summary of Contents for Terra Max HT1110-6.0M











































Search results

Summary of Contents for Terra Max HT1110-6.0M

Reviews:

Brands by name

Popular brands

GREAT PLAINS Terra Max HT1110-6.0M, Operator'S Manual

Search results

Summary of Contents for Terra Max HT1110-6.0M

Reviews:

Brands by name

Popular brands