manualshive.com logo in svg

GREAT PLAINS 3S-3000HD, Operator'S Manual

Share
Download
GREAT PLAINS 3S-3000HD Operator'S Manual Download Page 33

Great Plains Manufacturing, Inc.

Table of Contents Index

Operating Instructions

29

2019-03-12

Table of Contents Index

195-068M

Refer to Figure 22

5. Rotate cylinder lock channel up and forward off front 

box lift cylinder.

6. Slowly reverse the lift circuit lever and begin lowering 

the drill. Keep the circuit engaged until all three cylin-

ders are completely retracted. Set circuit to off or 

neutral.

The drill is now ready for unfolding.

Unfolding

Drill must be lowered from transport lift prior to unfolding. 

See “

Lowering Drill (Transport Lift)

” on page 28.

1. Verify that the site has clearance needed to unfold 

drill.

2. If markers are installed, set Marker/Fold valve at 

hitch to Fold.

Refer to Figure 24

3. Verify that the opener sub-frames are still raised and 

locked up (handles in ROAD position).

4. Slowly supply oil to base end of fold circuit. Unfold 

wing frames by completely extending fold cylinders.

FigureSpacer

Figure 23

Front Box Lift Cylinder

in Field Configuration

15553

Summary of Contents for 3S-3000HD





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands